Instrukcja obsługi Frigidaire IMKFD23A

Frigidaire Niesklasyfikowane IMKFD23A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Frigidaire IMKFD23A (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 4.5 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/4

P/N A23057901 210927

B. Ice Maker (x1) C. Ice Bucket (x1)

E. Shoulder Screws (x2) F. Screw (x1)

Cobra FRZ IM Numbers:

• CD: IMKFD23A

• SD: IMKFD28A

AUTOMATIC ICE MAKER

INSTALLATION INSTRUCTIONS

An authorized service technician is recommended to install the Ice Maker Kit.

Tools Needed:

• Phillips Screwdriver

• Flat-head Screwdriver

• ¼-inch Socket Wrench or Nut Driver

• Adjustable Wrench

Kit Components

P/N A23057901 210927

2. Use Phillips screwdriver to install two shoulder

screws (E) in the upper rear holes. Turn until

shoulder screws are in firm contact with freezer

wall. (See Figure 1).

7. Insert and tighten screw (F) in outermost hole on

bracket to fasten it to the upper side of freezer

wall. (See Figure 3).

Figure 1

Figure 3

Figure 2

8. Follow steps in Use & Care Manual to reinstall

door and add baskets.

9. Put Ice Bucket (C) on basket as shown in Figure 4.

Automatic Ice Maker Installation

1. Unplug refrigerator from electrical outlet.

NOTE

We recommend the freezer door and freezer

baskets be removed before proceeding with the

installation. Please refer to ‘Removing Freezer

Drawer’ in the “Removing the Doors” section and

‘Freezer Features’ in the “Storage Features” section

in the Use & Care Manual.

Figure 4

3. Remove the connector cover.

4. Plug the ice maker connector into the connector

in the freezer compartment.

5. Hang the ice maker and bracket assembly loosely

on the shoulder screws using the keyhole slots in

the bracket.

6. Push the Ice Maker and bracket assembly toward

the rear of the freezer compartment to seat the

keyhole slots firmly onto the shoulder screws (See

Figure 2).

NOTE

Verify the switch is in the ON position.

Connector Cover

Switch

Connector

P/N A23057901 210927

Before Installing The Water Supply Line, You Will

Need:

• Basic Tools: adjustable wrench, flat-head

screwdriver, and Phillips screwdriver

• Access to a household cold water line with water

pressure between 30 and 100 psi.

• A water supply line made of inch (6.4mm) OD, ¼

copper or stainless steel tubing. To determine the

length of tubing needed, measure the distance

from the ice maker inlet valve at the back of the

refrigerator to your cold water pipe. Then add

approximately 7 feet (2.1 meters), so the refrigerator

can be moved out for cleaning (as shown).

• A shuto valve to connect the water supply line to ff

your household water system. DO NOT use a self-

piercing type shutoff valve.

• Do not reuse compression fitting or use thread

seal tape.

• A compression nut and ferrule (sleeve) for

connecting a copper water supply line to the ice

maker inlet valve.



NOTE

Check with your local building authority for

recommendations on water lines and associated

materials prior to installing your new refrigerator.

Depending on your local/state building codes,

Electrolux recommends for homes with existing

valves its Smart Choice® water line kit 5305513409

(with a 6 ft. Stainless Steel Water Line) and for

homes without an existing valve, Electrolux

recommends its Smart Choice Water® line kit

5304490717 (with a 20 ft. Copper Water Line with

self-tapping saddle valve). Please refer to

www.electrolux.com for more information.

Figure 1

Plastic Water

Tubing to Ice

Maker Fill

Tube

Steel

Clamp

Brass

Compression

Nut

Ferrule

(Sleeve)

Copper

water line

Water Valve

Bracket

Valve Inlet

Water Valve

Copper water line

from household

water supply

(Include enough tubing in loop to allow

moving refrigerator out for cleaning.)

To Connect Water Supply Line To Ice Maker Inlet

Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket.

Turn ON water supply and flush supply line until

water is clear. Turn OFF water supply at shutoff valve.

3. Remove plastic cap from water valve inlet and

discard cap.

4. If you use copper tubing - Slide brass compression

nut, then ferrule (sleeve) onto water supply line.

Push water supply line into water valve inlet as far

as it will go ( inch/6.4 mm). Slide ferrule (sleeve) ¼

into valve inlet and finger tighten compression

nut onto valve. Tighten another half turn with a

wrench; DO NOT overtighten. See Figure 1.

IMPORTANT

Ensure that your water supply line connections

comply with all local plumbing codes.

CAUTION

To Avoid Property Damage:

• Copper or Stainless Steel braided tubing is

recommended for the water supply line. Water

supply tubing made of inch plastic is not ¼

recommended to be used. Plastic tubing greatly

increases the potential for water leaks, and the

manufacturer will not be responsible for any

damage if plastic tubing is used for the supply line.

• DO NOT install water supply tubing in areas

where temperatures fall below freezing.

• Chemicals from a malfunctioning softener

can damage the ice maker. If the ice maker is

connected to soft water, ensure that the softener

is maintained and working properly.

Connecting Ice Maker to Water Supply

WARNING

To avoid electric shock, which can cause death or

severe personal injury, disconnect the refrigerator

from electrical power before connecting a water

supply line to the refrigerator.

Specyfikacje produktu

Marka:	Frigidaire
Kategoria:	Niesklasyfikowane
Model:	IMKFD23A
Kolor produktu:	Czarny, Srebrny
Typ produktu:	Frytkownica niskotłuszczowa
Regulowany termostat:	Tak
Moc:	1500 W
Typ kontroli:	Dotyk
Wbudowany wyświetlacz:	Tak
Łatwy do czyszczenia:	Tak
Długość przewodu:	1 m
Typ wyświetlacza:	LED
Położenie urządzenia:	Autonomiczny
Wysokość produktu:	330 mm
Szerokość produktu:	355 mm
Głębokość produktu:	280 mm
Waga produktu:	4420 g
Podręcznik użytkownika:	Tak
Temperatura (maks):	200 °C
Wskaźnik pozostałego czasu:	Tak
Minutnik:	60 min
Powłoka nieprzywierająca:	Tak
Stopy antypoślizgowe:	Tak
Materiały:	Polipropylen (PP)
Pojemność:	2.5 l
Rodzaj konstrukcji:	Pojedyńczy
Temperatura (min):	150 °C
Uchwyt(y):	Tak
Części wodoodporne:	Tak
Zdejmowalna misa:	Tak
Podświetlony włącznik/wyłącznik:	Tak
Zawartość opakowania:	Hetelucht friteuse, frituurpan, frituurmand, frituurmandverdeler, handleiding.
Sygnał zakończenia gotowania:	Tak
Nienagrzewający się uchwyt:	Tak
Wydajność smażenia:	0.8 kg
Zegar cyfrowy:	Tak
Nienagrzewająca się obudowa:	Tak
Miska z nieprzywieralnego materiału:	Tak
Smażenie niskotłuszczowe:	Tak