Instrukcja obsługi Fujitsu MAW 3300 NP

Fujitsu dysk twardy MAW 3300 NP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fujitsu MAW 3300 NP (2 stron) w kategorii dysk twardy. Ta instrukcja była pomocna dla 33 osób i została oceniona przez 17 użytkowników na średnio 4.7 gwiazdek

Pobierz PDF

Strona 1/2

MAW3300NC/NP, MAW3147NC/NP,

MAW3073NC/NP

DISK DRIVES INSTALLATION GUIDE

CARE OF YOUR FUJITSU DRIVE

Careful handling and installation of your disk drive is paramount to the longevity of the unit. Serious damage can occur to the internal

mechanisms if forces outside the environmental specifications are exerted to the casing. In transportation, always use the original packing

in which the drive was supplied and avoid sharp changes in temperature to minimise the risk of condensation.

Handling

1. Never drop. Handle with care.

2. Never move the disk drive while the disks are spinning. This is when the drive is powered on and also immediately after power off.

Refer to the Start/Stop specification for your drive.

3. Always turn off the power before connecting or disconnecting the interface cable. The same applies to changing any of the switches or

terminal settings except Write protect switch on NP model drives.

4. Never place the drive in the vicinity of strong magnetic fields such as monitors, televisions, or loudspeakers.

5. Never use any cleaning agents or liquids on the drive.

6. Always use an antistatic mat and wrist strap when handling the drive. Hold the drive by the Base casting and never touch the components

on printed circuit board.

7. Never remove any labels from the drive and do not deface them in any way; these labels are part of the disk drive design.

8. Never open the disk enclosure for any reason. Doing so voids any warranty.

9. Always pay close attention to the mounting specifications such as sway space and cooling. If the temperature difference between storage

location and installation locations is more than 10°C, leave the drive in the new location for at least two hours for Temperature acclimation.

This minimises any risk of condensation forming on the drive.

The Drive needs NO preventative or periodic maintenance during its life time if properly used in the correct environment.

INSTALLATION

1. ORIENTATION–The drive can be installed in each six surface down orientations. Inclination from vertical or horizontal should not

exceed 5°.

2. MOUNTING SCREW INSTALLATION–When the mounting screw holes on the side of the drive are used, be sure to use the two pairs

of outer holes. Do not use the center hole in conjunction with only one of the outer holes. The screws must not penetrate the drive by more

than 5.0 millimeters. Impact caused by the electric driver must be within the device specifications.

3. COOLING–Allow space above and below the drive to provide an adequate air flow. Fan cooling is recommended. The disk enclosure

temperature measured at center of base cover (label side) should never exceed 60°C. See Table 1.

Table 1. Reference value of airflow

Environmental temperature Required velocity of airflow

35°C > 0.2m/s

40°C > 0.5 m/s

45°C > 0.9 m/s

50°C > 1.5 m/s

4. TERMINATION–A terminator should be installed externally at both ends of the SCSI bus.

5. TERMINATOR POWER–Terminator power must be supplied to terminator for correct operation. This can be supplied from either the

drive, except for NC model or the SCSI bus. If only NC model drives are connected to the SCCI bus, terminator power should be supplied

externally.

6. ATTACHING THE CABLES–To avoid possible damage to the drive, make sure the direction of the connector matches.

CAUTION: Warranty may be avoided if damage to the connector is caused by wrong insertion.

FUJITSU LIMITED

Storage Products Group

4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan

USA http://www.fcpa.com/

EUROPE http://www.fujitsu-europe.com/

C141-E227-01EN

Specyfikacje produktu

Marka:	Fujitsu
Kategoria:	dysk twardy
Model:	MAW 3300 NP
Wysokość produktu:	25.4 mm
Szerokość produktu:	101.6 mm
Głębokość produktu:	146 mm
Waga produktu:	750 g
Wewnętrzny:	Tak
Zakres temperatur (eksploatacja):	5 - 55 °C
Zakres wilgotności względnej:	5 - 95 %
Pobór mocy:	9.5 W
Zakres temperatur (przechowywanie):	-40 - 70 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Standardowe rozwiązania komunikacyjne:	Ultra320 SCSI
Wymiary produktu (SxGxW):	101.6 x 143 x 25.4 mm
Dopuszczalna wysokość podczas eksploatacji (n.p.m.):	0 - 3000 m
MTBF (Średni okres międzyawaryjny):	1200000 h
Pojemność HDD:	300 GB
Rozmiar bufora dysku pamięci:	8 MB
Dopuszczalna wysokość (n.p.m.):	0 - 12000 m
Wstrząsy podczas pracy:	65 G
Średnie opóźnienie:	2.99 ms
Czas wyszukiwania między ścieżkami:	0.2 ms
Pełne wyszukiwanie seek time:	10 ms
Średni czas poszukiwania:	4.5 ms
Wstrząsy podczas przechowywania:	225 G
Wibracje podczas pracy:	0.6mm (5 - 20 Hz)/ 1.0G (20 - 300 Hz) G