Instrukcja obsługi Fujitsu MBA3300NP

Fujitsu dysk twardy MBA3300NP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fujitsu MBA3300NP (2 stron) w kategorii dysk twardy. Ta instrukcja była pomocna dla 33 osób i została oceniona przez 17 użytkowników na średnio 3.5 gwiazdek

Pobierz PDF

Strona 1/2

CARE OF YOUR FUJITSU HARD DISK DRIVE (HDD)

Careful handling and installation of your HDD is paramount to the longevity of the unit. The internal mechanism of the HDD can be

seriously damaged if the HDD is subjected to forces outside the environmental specifications. When transporting the HDD, always use the

original packaging in which the HDD was delivered to you, and avoid exposing the HDD to extreme changes in temperature to minimize the

risk of condensation.

Handling

1. Never drop the unit. Handle it with care.

2. Never move the HDD while the disks are spinning. Note that the disks spin when the HDD is powered on and also immediately after

power off. Refer to the Start/Stop specification for your HDD.

3. Always turn off the power before connecting or disconnecting the interface cable. The same applies to changing any of the switches or

terminal settings except Write protect switch on NP model drives.

4. Never place the HDD in the vicinity of equipment giving off strong magnetic fields, such as CRT monitors, televisions, or loudspeakers.

5. Never use any cleaning agents or liquids on the HDD.

6. Always use an antistatic mat and wrist strap when handling the HDD. Hold the HDD by the base casting and never touch the components

on printed circuit board assembly.

7. Never remove any labels from the HDD or deface them in any way.

8. Never open the HDD for any reason. Doing so will void any warranties.

9. Always pay close attention to the mounting specifications such as those for sway space and cooling. If the temperature difference

between the storage location and installation locations exceeds 10°C, for temperature acclimation purposes, leave the HDD in the new

location for at least two hours before turning it on. This minimizes any risk of condensation forming on the HDD.

The HDD needs NO preventative or periodic maintenance during its service life if properly used in the appropriate environment.

INSTALLATION

1. ORIENTATION–The HDD can be installed flat on any of its six sides. Inclination from vertical or horizontal plane should not exceed

5°.

2. MOUNTING SCREW INSTALLATION–When the mounting screw holes on the side of the HDD are used, be sure to use the two pairs

of outer holes. Do not use the center hole in conjunction with only one of the outer holes. The screws must not penetrate the HDD by more

than 5.0 millimeters. Impact caused by the electric screwdriver must be within the HDD specifications.

3. COOLING–Allow space above and below the HDD to provide an adequate air flow. Fan cooling is recommended. The HDD

temperature measured at center of top cover (label side) should never exceed 60°C. See Table 1.

Table 1. Reference value of airflow

Environmental temperature Required velocity of airflow

30°C > 0.3m/s

35°C > 0.6 m/s

40°C > 0.9 m/s

45°C > 1.5 m/s

4. TERMINATION–A terminator should be installed externally at both ends of the SCSI bus.

5. TERMINATOR POWER–Terminator power must be supplied to terminator for correct operation. This can be supplied from either the

HDD, except for NC model or the SCSI bus. If only NC models are connected to the SCCI bus, terminator power should be supplied

externally.

6. CONNECTING–To avoid potential damage to the HDD, make sure that connector type and orientation is correct.

CAUTION: Your warranty may be voided if the connector is damaged as a result of incorrect insertion.

MBA3300NC, MBA3300NP, MBA3147NC, MBA3147NP,

MBA3073NC, MBA3073NP

HARD DISK DRIVES INSTALLATION GUIDE

FUJITSU LIMITED

Storage Products Group

4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan

C141-E271-01EN

http://www.fujitsu.com/

Undermentioned information is effective only in EU for traceability of the EMC Directive

Manufacturer:

Fujitsu Limited

4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan

Authorized representative importer / distributor in EU:

Fujitsu Europe Limited

es Park Central, Ha

es End Road, Ha

es, Middlesex, UB4 8FE, United Kin

dom

Specyfikacje produktu

Marka:	Fujitsu
Kategoria:	dysk twardy
Model:	MBA3300NP
Wysokość produktu:	25.4 mm
Szerokość produktu:	101.6 mm
Głębokość produktu:	146 mm
Waga produktu:	750 g
Napięcie pracy:	5 / 12 V
Wewnętrzny:	Tak
Zakres temperatur (eksploatacja):	5 - 55 °C
Zakres wilgotności względnej:	5 - 95 %
Pobór mocy:	12.8 W
Zakres temperatur (przechowywanie):	-40 - 70 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Standardowe rozwiązania komunikacyjne:	SATA
Wymiary produktu (SxGxW):	101.6 x 143 x 25.4 mm
Dopuszczalna wysokość podczas eksploatacji (n.p.m.):	0 - 3000 m
MTBF (Średni okres międzyawaryjny):	1400000 h
Pojemność HDD:	300 GB
Szybkość HDD:	15000 RPM
Rozmiar HDD:	3.5 "
Rozmiar bufora dysku pamięci:	16 MB
Dopuszczalna wysokość (n.p.m.):	0 - 12000 m
Wstrząsy podczas pracy:	65 G
Średnie opóźnienie:	2.00 ms
Czas wyszukiwania między ścieżkami:	0.2 ms
Pełne wyszukiwanie seek time:	8 ms
Średni czas poszukiwania:	3.4 ms
Wstrząsy podczas przechowywania:	250 G
Wibracje podczas pracy:	0.6mm (5 - 20 Hz)/ 1.0G (20 - 300 Hz) G
Wibracje podczas przechowywania:	3.1mm (5 - 20 Hz)/ 5.0G (20 - 300Hz) G