Instrukcja obsługi Fujitsu MBC2073RC

Fujitsu dysk twardy MBC2073RC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fujitsu MBC2073RC (1 stron) w kategorii dysk twardy. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 13 użytkowników na średnio 4.4 gwiazdek

Pobierz PDF

Strona 1/1

MBC2073RC, MBC2036RC

HARD DISK DRIVES INSTALLATION GUIDE

CARE OF YOUR FUJITSU HARD DISK DRIVE (HDD)

Careful handling and installation of your HDD is paramount to the l

ongevity of the unit. The internal mechanism of the HDD can

seriously damaged if the HDD is subjected to forces outside the

environmental specifications. When transporting the HDD, alway

s use the

original packaging in which the HDD was delivered to you, and avoid exposing the HDD to extreme changes in temperature to minimize the

risk of condensation.

HANDLING

1. Never drop the unit. Handle it with care.

2. Never move the HDD while disks are spinning. Note that the disks spin when the HDD is powered on and also immediately after power

off. Refer to the Start/Stop specification for your HDD.

3. Never place the HDD in the vicinity of equipment giving off strong magnetic fields, such as CRT monitors, televisions, or loudspeakers.

4. Never use any cleaning agents or liquids on the HDD.

5. Always use an antistatic mat and wrist strap when handling the HDD. Hold the HDD by the base casting and never touch the components

on the printed circuit board assembly.

6. Never remove any labels from the HDD or deface them in any way.

7. Never open the HDD for any reason. Doing so will void any warranties.

8. Always pay close attention to the mounting specifications such as those for sway space and cooling. If the temperature difference

between the storage location and installation location exceeds 10°C, for temperature acclimation purposes, leave the HDD in the new

location for at least two hours before turning it on. This minimizes any risk of condensation forming on the HDD.

The HDD needs NO preventative or periodic maintenance during its service life if properly used in an appropriate environment.

INSTALLATION

1. ORIENTATION

The HDD can be installed flat on any of its six sides. Inclination from a vertical or horizontal plane should not exceed 5°.

2. MOUNTING SCREW INSTALLATION

Use all of 4 mounting screw holes on both sides of the HDD or the bottom. The inward projection of the screw from the HDD frame wall

at the corner must be 2.5 mm ±0.5 mm. Impact caused by the electric screwdriver must be within the HDD specifications.

3. COOLING

Allow space above and below the HDD to provide an adequate airflow. Fan cooling is recommended. The HDD temperature measured

on the cover surface (label side) should never exceed 60°C. See Table 1.

Table 1. Reference value of airflow

Environmental temperature Required velocity of airflow

35 °C > 0.2 m/s

40 °C > 0.6 m/s

45 °C > 1.1 m/s

50 °C > 1.8 m/s

4. BREATHING

Never cover the vent hole displayed on the label with the arrow.

5. CONNECTING

To avoid potential damage to the HDD, make sure that connector type and orientation is correct.

CAUTION: Your warranty may be voided if the connector is damaged as a result of incorrect insertion.

FUJITSU LIMITED

Storage Products Group

4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan

Undermentioned information is effective only in EU for traceability of the EMC Directive

Manufacturer :

Fujitsu Limited

4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-8588, Kanagawa-ken, Japan

Authorized representative importer / distributor in EU :

Fujitsu Europe Limited

Hayes Park Central, Hayes End Road, Hayes, Middlesex, UB4 8FE, United Kingdom

C141-E265-01EN

Specyfikacje produktu

Marka:	Fujitsu
Kategoria:	dysk twardy
Model:	MBC2073RC
Wysokość produktu:	15 mm
Szerokość produktu:	69.85 mm
Głębokość produktu:	100.45 mm
Waga produktu:	220 g
Napięcie pracy:	5 V
Wewnętrzny:	Tak
Zakres temperatur (eksploatacja):	5 - 55 °C
Zakres wilgotności względnej:	5 - 95 %
Pobór mocy:	5.3 W
Zakres temperatur (przechowywanie):	-40 - 70 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Standardowe rozwiązania komunikacyjne:	SAS
Wymiary produktu (SxGxW):	69.85 x 100.45 x 15 mm
Dopuszczalna wysokość podczas eksploatacji (n.p.m.):	0 - 3000 m
Pojemność HDD:	73.5 GB
Szybkość HDD:	15000 RPM
Rozmiar HDD:	2.5 "
Rozmiar bufora dysku pamięci:	16 MB
Dopuszczalna wysokość (n.p.m.):	0 - 12000 m
Wstrząsy podczas pracy:	100 G
Średnie opóźnienie:	2.00 ms
Czas wyszukiwania między ścieżkami:	0.2 ms
Pełne wyszukiwanie seek time:	6 ms
Średni czas poszukiwania:	3 ms
Wstrząsy podczas przechowywania:	400 G
Wibracje podczas pracy:	0.6mm (5 - 20 Hz)/ 1.0G (20 - 300 Hz) G
Wibracje podczas przechowywania:	3.1mm (5 - 20 Hz)/ 5.0G (20 - 300Hz) G