Instrukcja obsługi Kathrein UFO 83
Kathrein
Niesklasyfikowane
UFO 83
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kathrein UFO 83 (11 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 11.5 użytkowników na średnio 4.3 gwiazdek
Strona 1/11
1 / 8
Head-end 8-way DVB-S(2)/-T(2)/-C – DVB-T (COFDM)
UFO 83 20610134
About This Manual
This document is part of the product.
►Install and use the unit only after you have read and
understood this document.
►Keep this document for reference throughout the life of
the device. Pass this document on to the next owner
and user of the device.
For the current version of this manual, go to the Kathrein
website www.kathrein-ds.com.
Features
■Stand-alone head-end with 8-way multi-standard
frontend DVB-S(2)/-T(2)/-C and 8output channels
conforming to DVB-T (exibly congurable)
■Outstanding output values due to direct implementa-
tion as FPGA solution
■High level of energy efciency
■4 Sat-IF inputs with DiSEqCTM
1.0 functionality for sat
multi-switches and 1terr./cable input, exibly distribut-
able across 8 multi-standard frontends
■Power supply for LNB and active antennas
■All transmission parameters can be set using the
USW800 conguration software
■Remote maintenance and conguration
■Comprehensive baseband signal processing with
channel lter functionality such as NIT, LCN
■Cascade capability for two head-ends (16-way multi-
standard frontend and 16xDVB-T) for common
conguration and NIT generation incl. LCN
■No fan, therefore no noise and no maintenance
Scope of supply
●UFO 83
●Wall mounting plate
●User instructions
●Third Party Software Acknowledgement
Function blocks
8 x DVB-
S2/-T2/-C
4 x Sat-IF/
1 x terr./cable
DiSEqC™
Channel
filter 8 x DVB-T
Input Frontend Baseband Output
Special features
Energy-
efficient
Thermal
cut-out
Matrix
5 to 8
Power supply LNB
and
current antennas
NIT
generation
CAT
matching
Extended
LCN
processing
3 Watt/COFDM
(typical) 1)
1) typical for the following input: 4x DVB-S, 2x DVB-S2, 2x DVB-T2, no LNB/antenna supply
IMPORTANT
Read carefully
before use!
2 / 8
Intended Use
The UFO83 is used for transmodulation of DVB signals. The latest triple-tuner technology makes it possible to receive
up to eight DVB-S(2)/ -T(2)/ -C transponders. These can be received from the four Sat-IF inputs with DiSEqC
TM function-
ality and the terrestrial/cable input in any combination. The UFO83 delivers up to eight individually congurable output
channels conforming to DVB-T.
The highly efcient baseband signal processing offers channel lter, NIT, CAT and LCN functionality. The conguration
is carried out by means of the USW800 management software over an IP interface. An optional cascading of two units
(UFO83 or/and UFO83/CI) is possible via a USB connection.
The unit is intended exclusively for the application in the UFG810 as well as in satellite, cable or antenna reception
systems. Any other use of failure to comply with these instructions will result in voiding of the guarantee or warranty.
General safety instructions
●The device can be connected to the power supply and disconnected from it only by means of the power plug. Make
sure that the connected power plug is always freely accessible and easy to reach.
●If the casing is damaged, do not connect the device to the power supply.
●If the device and/or the cables connected to it are damaged, immediately disconnect the system from the power
supply. Do not switch the system on again until
–the device has been repaired by the dealer or manufacturer,
–and the cables connected have been repaired by a competent person.
●Do not open the casing and do not modify the device. Otherwise the guarantee and warranty will become void.
●Never cover the cooling ribs or the air circulation openings.
●Do not modify, remove or disgure the notices and markings applied by the manufacturer.
●Refer to the manufacturer's documentation before connecting external components other than those described
in this document (such as computers, network components). Incorrectly connected components can damage the
device.
●Refer to the current issue of the safety requirements EN60728-11 and EN60065.
●Disconnect the device from the power supply before performing mechanical work on the system.
WARNING
Risk of burns from hot surfaces!
In the event of a defect the heat sink of the unit may exceed 70°C.
►Do not touch the heat sink when the device is in operation or has recently been in operation.
Note
In the event of overheating, the device will shut down automatically and after it has cooled down will switch
on again automatically.
Transportation and Storage
►Transport and storage the unit in its original packaging.
►Protect the unit against dust, dirt, moisture and direct sunlight.
►Transport and store the unit in the permissible temperature range from –25 to +70°C. Make sure there is no water
condensation bildup.
3 / 8
Arrangement and function
Device elements
1
2
3
4
78
8
9
6
5
10
11
12
13
USB
UFO Link
Fig. 1: Device elements
①4x Sat-IF input, F socket ⑨Earthing screw
②1x terrestrial/cable input, F socket ⑩Power supply1)
③Screw for xing to the wall mounting plate ⑪Master LED; see below for more info.
④Test output, signal level –25dB, F socket ⑫Status LED; see below for more info.
⑤DVB-T output, F socket ⑬Reset button; see below for more info.
⑥Network port, RJ45
⑦USB port, type B, communications interface for connection to the UFOmini UFOlink master
2)
⑧2x USB ports, typeA:
USB: Software update by USB stick
UFO link UFOlink slave: Communications interface for connection to the UFOmini 3)
1) The power supply cable is integral to the device and is not shown here.
2) If the head-end is the slave; see below for more info , P.5.Cabling
3) If the head-end is the master; see below for more info , P.5. Cabling
LEDs and reset button
Master LED
green the head-end is the
master
off the head-end is a slave
Status LED
green OK
green, ashing software update in progress
red error
orange head-end starting
orange, ashing head-end is being identied by the
USW800 conguration software
Reset button
Press <5s1) the head-end .will reboot
Press >5s1) the head-end will reset to the and will reboot. factory settings Do not release the
reset button until the status LED lights up orange.
Press >5s1) the head-end will look for an update on the connected USB stick, perform the
update and reboot.2)
1) To prevent accidental activation, the reset button is recessed. To activate the reset button, use a tool such as a ball-point pen.
2) Pre-requirement: There is a valid update le on the USB stick. See the USW800 conguration software for more info.
Specyfikacje produktu
| Marka: | Kathrein |
| Kategoria: | Niesklasyfikowane |
| Model: | UFO 83 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Kathrein UFO 83, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Kathrein
28 Stycznia 2025
5 Października 2024
28 Września 2024
22 Września 2024
21 Września 2024
20 Września 2024
19 Września 2024
17 Września 2024
14 Września 2024
13 Września 2024
Instrukcje Niesklasyfikowane
- Niesklasyfikowane Arylic
- Niesklasyfikowane Eden
- Niesklasyfikowane Aida
- Niesklasyfikowane Karma
- Niesklasyfikowane Konica Minolta
- Niesklasyfikowane Now TV
- Niesklasyfikowane Steren
- Niesklasyfikowane Emmaljunga
- Niesklasyfikowane Grendel
- Niesklasyfikowane SeaLife
- Niesklasyfikowane Valore
- Niesklasyfikowane Selfsat
- Niesklasyfikowane Rinnai
- Niesklasyfikowane DLO
- Niesklasyfikowane Analog Way
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025