Instrukcja obsługi MB Quart MBQR-RAD-2
MB Quart
Niesklasyfikowane
MBQR-RAD-2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla MB Quart MBQR-RAD-2 (59 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/59
DASHBOARD
DISASSEMBLY INSTRUCTIONS
for Polaris® RZR® Vehicles
Instruction Manual
MBQR-RAD-2
2©2020 Maxxsonics USA, Inc.
THANK YOU!
Congratulations for choosing the MBQR-RAD-2, an AM/FM/WB, USB and Bluetooth
Multimedia Controller by MB Quart. The unit and housing are engineered to t 2013 and
newer Polaris® RZR® vehicles. For more detailed information about the product, the
operator/install manual* and a video tutorial, please visit MBQuart.com.
*Wiring information, installation steps and operation of the MBQR-RAD-2 source unit are in the
Operator's Guide and Installation Instructions pictured at right.
INSTALLATION TIME
About 1.5 hours are required to complete this installation, not including other system
components. These instructions are for dashboard disassembly only.
TOOLS AND SUPPLIES NEEDED
● Wire Strippers and Crimpers ● Flush Cut Wire Cutters (for trimming zip-ties)
● Bojo Tools (Pry Tools) ● T40 Torx Driver
● Ratchet w/ 10mm Socket ● T25 Torx Driver
● (Optional) Soldering iron, solder and heat shrink tubing or high-quality electrical tape
SAFETY PRECAUTIONS
Safely prepare your machine for the MBQR-RAD-2 installation before proceeding.
● Turn the ignition off and remove the key
● Use a packing blanket other soft material to protect your machine
● Safety Glasses - always wear eye protection
PREPARATION FOR INSTALLATION
Before dismantling your vehicle, we suggest you prepare your tools, the MBQR-RAD-2 and its wiring as
increases efciency to have everything ready when each component is installed.
STEP 1 – REMOVE SEATS
Remove driver and passenger seats by pulling on the
lock clip shown in Figure 1-1 This lock clip is located
between the bottom and upright portion of the seat.
Removing both seats will give you the room to work in
the kick panel areas, in addition to getting access to the
battery for Step 2.
STEP 2 – REMOVE NEGATIVE BATTERY CABLE
Using a 10mm socket and ratchet, remove the negative
battery terminal and set aside as shown in Figure 1-2.
This safety measure ensures you do not have any
accessories powered during the installation, as well as
keeps the battery from unnecessarily draining.
Figure 1-1
Figure 1-2
PRE-INSTALLATION
Operator’s Guide and
Installation Instructions
MBQR-RAD-2
AM/FM/USB/Blu etooth®
Mul timedi Contr oller and a
fo Polarisr ® RZR® Vehicles
MBQR-RAD-2
Operator's Guide and
Installation Instructions
3
DISASSEMBLY
DASH AREA DISASSEMBLY 2013-2018 (Non-Turbo S) RZR
Please note, separate disassembly instructions for the 2018.5 Turbo S and 2019+ RZR models are found on
pages 5-8 in this manual.
STEP 1 – REMOVE CENTER HOOD
Start with removing the hood as shown in Figure 5-1.
Twist the tabs at the upper left and right corners. Pull
up to remove. This is where you will access the bus
bar to make power connections for your source unit.
Conrm that your machine has the bus bar harness
installed. If your bus bar harness has not been installed,
you can purchase from your dealer or Polaris online.
The part numbers are 2881551 or 2881646 depending
on which specic RZR model you own.
STEP 2 - REMOVE TOP OF DASH
Remove (2) T40 screws as shown in Figure 5-2. Slide
dash forward to access back of dash and unplug gauges and switches one at a time. Set dash aside in a
safe location. This will provide wiring access.
STEP 3 – REMOVE THE GRAB BAR
Remove the grab bar as shown in Figure 5-3 by removing the retaining clip and pin and rmly pulling the
grip toward the rear of the vehicle.
STEP 4 - REMOVING DASH POCKET & REAR MOUNT
To remove the DIN dash pocket from the dash, locate the rear support bracket at the rear of the pocket and
remove the T40 Torx head screw as in Figure 5-4. Next, remove the clip shown on the right from the back
and pull out the plastic pocket. Set aside the retaining clip shown in Figure 5-5 for re-use when mounting the
MBQR-RAD-2 source unit.
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
T40 Torx Screw
Set aside OEM dash clip for source unit mounting
later in the installation as its reused when you are
installing an MB Quart MBQR-RAD-2.
Figure 5-5
Specyfikacje produktu
| Marka: | MB Quart |
| Kategoria: | Niesklasyfikowane |
| Model: | MBQR-RAD-2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z MB Quart MBQR-RAD-2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane MB Quart
28 Września 2024
16 Września 2024
3 Września 2024
27 Sierpnia 2024
24 Sierpnia 2024
20 Sierpnia 2024
19 Sierpnia 2024
19 Sierpnia 2024
18 Sierpnia 2024
16 Sierpnia 2024
Instrukcje Niesklasyfikowane
- Niesklasyfikowane Mega
- Niesklasyfikowane Reebok
- Niesklasyfikowane Liemke
- Niesklasyfikowane Teka
- Niesklasyfikowane Canyon
- Niesklasyfikowane DEHN
- Niesklasyfikowane CommScope
- Niesklasyfikowane Tot Tutors
- Niesklasyfikowane Deltronic
- Niesklasyfikowane Eminent
- Niesklasyfikowane Soundmaster
- Niesklasyfikowane Sunpentown
- Niesklasyfikowane Laica
- Niesklasyfikowane Nabo
- Niesklasyfikowane Potenza
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025