Instrukcja obsługi Moultrie Pro Magnum Feeder
Moultrie
Niesklasyfikowane
Pro Magnum Feeder
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Moultrie Pro Magnum Feeder (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
Drum
Feeder
Kit
Turn drum over, measure and mark the center of the bottom.
Center the provided template on the bottom of the drum
and secure with tape. Drill three 5/16" Feeder Leg Holes.
Using a Hole Saw, drill a 2-1/4" hole in the center of the
bottom of your drum.
caution: wear eye protection
Pro Magnum will mount to the bottom of any drum or bucket
Inside Drum
Outside Drum
Bolt
Flat Nut
Feeder Mounting
Holes
Instructions for Pro Magnum Feeder
THANK YOU for your purchase of the Pro Magnum Feeder. Please read this sheet before
operating the unit. If you should have any questions about this product or any other Moultrie
product, please contact us using the information on the back of this sheet. To help us to
better serve you and to activate your Lifetime Warranty, please submit your warranty
information online at http://www.moultriefeeders.com/warranty
DRILLING YOUR DRUM/BARREL/BUCKET
A
MOUNTING THE FEEDER
B
Turn drum over, measure and mark the center of the bottom.
Center the provided template on the bottom of the drum
and secure with tape. Drill three 5/16” Feeder Leg Holes.
Using a Hole Saw, drill a 2.25” hole in the center of the
bottom of your drum.
From the inside of the drum, slide the three provided Bolts
through the holes on the bottom and into the provided
Flat Nuts. From the inside, using a Phillips head screwdriver,
turn the Bolt clockwise until the Flat Nut is tight against
the bottom.
Slide feeder over three Bolts that are sticking rmly through
the bottom of the drum. Attach Feeder Kit to the Drum
using the three provided Wing-Nuts.
Pro Magnum will mount to the bottom of any drum or bucket
NOTE: If you purchased a Moultrie barrel, go to step II
DO NOT EXCEED 400 LBS
OF FEED IN 55-GAL FEEDERS
Pro Magnum
Feeder Kit
Belly Band
Ring
Bolt
Spacer
Lock
Washer
Nut
NOTE: DO NOT LOAD FEEDER until it is standing up and in place (see Section E).
DO NOT EXCEED 200 LBS
OF FEED IN 30-GAL FEEDERS
Belly Band
Ring
Slide the bolt through the Belly Band Ring, Spacer and
Lock Washer as shown. Tighten nut on bolt until metal
Belly Band Ring tabs are touching spacer on each side.
Turn the Metal Drum upside down and slide the Belly Band Ring
around perimeter and make sure that belly band is snug against
the bottom structure ring as shown (Moultrie barrel only).
Specyfikacje produktu
| Marka: | Moultrie |
| Kategoria: | Niesklasyfikowane |
| Model: | Pro Magnum Feeder |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Moultrie Pro Magnum Feeder, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Moultrie
3 Października 2024
Instrukcje Niesklasyfikowane
- DeWalt
- Eltako
- Cherry
- Peerless-AV
- Berger & Schröter
- Roline
- FontaFit
- Elation
- Propellerhead
- LogiLink
- Powerblade
- Technicolor
- Exo-Terra
- Hooker
- Polti
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025