Instrukcja obsługi Oricom Wake 'N' Shake Dynamite WNS80
Oricom
Niesklasyfikowane
Wake 'N' Shake Dynamite WNS80
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Oricom Wake 'N' Shake Dynamite WNS80 (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 5 użytkowników na średnio 4.9 gwiazdek
Strona 1/1
1 32 4
INSTALLATION
Plug the supplied AC/DC adaptor (Model No. 2T0069) to an AC household outlet, and
then plug the DC jack to the back of the unit. Your clock is ready to work for you.
TO SET TIME AND THE SNOOZE DURATION
1. Press SET once, the hour digits “ ” flash. Press or to set the time in hours (hold 0▲ ▼
to advance rapidly).
2. Press SET again, the minute digits “ ” flash. Press or to set the time in minutes. 00 ▲ ▼
(hold to advance rapidly).
3. Press SET again, the display shows “ ” and flashes. Press or to select 24Hr ▲ ▼
“12Hr” or “24Hr” time format. If “ ” is selected, the will appear on the upper 12Hr AM
left to indicate the morning time and will appear on the upper right to indicate the PM
afternoon.
4. Press SET again, the display shows “ ” and flashes. Press or to select your 05 ▲ ▼
snooze time from 5 to 60 minutes.
5. Press again or if no key pressed for approx. 10 seconds to exit the setting mode.SET
TO SET THE ALARM
1. Press and hold appear and the alarm’s hour digits flash. Press AL SET / AL STOP, AL
▲ ▼ or to set the alarm in hours. (Hold or to advance rapidly).▲ ▼
2. Press AL SET / AL STOP once again, the minute digits flash. Press or to set the ▲ ▼
alarm in minutes. (Hold or to advance rapidly).▲ ▼
3. Press AL SET / AL STOP again, LED displays “HI” (vibration at HI level), press or ▲ ▼
to select “ ” (vibration at Lo level).LO
4. Press AL SET / AL STOP once again, LED displays “F-1 (ex. 800 Hz)” and flash, press
▲ ▼ or to select the alarm tone (frequency) :
F-1 (low tone, 800 Hz),
F-2 (mid tone, 1 KHz),
F-3 (high tone, 1.5 KHz)
5. Press AL SET / AL STOP again, LED displays “ ” ( for the Low ringer level), press L1 ▲
or ▼ to select “L3” (for the high ringer level)
6. Press AL SET / AL STOP once again to exit the alarm setting, also if no buttons are
pressed for around 10 seconds this will also exit the alarm setting mode.
TO TURN ON/OFF AND SELECT THE ALARM MODE
1. At normal time display mode, press one at a time to activate the AL SET / AL STOP
alarm(s) and turn on corresponding alarm indicator(s) on the lower part of the display:
: only shaker activated
: both sound and shaker alarm activated
: both strobe light and shaker alarm activated
: strobe light, sound and shaker alarm activated
2. Press AL SET / AL STOP once more to turn off all the alarms, all , and
alarm indicators are turned off.
Note: To use the shaker alarm, please plug in the shaker plug to the back of the clock. If
user doesn’t want to use the shaker alarm, unplug the shaker plug from the clock.
TO STOP AND RESET THE ALARM TO COME ON THE NEXT DAY
When alarm is sounding, the corresponding alarm indicator flashes. Press AL SET / AL
STOP once to stop the alarm and reset it to come on the following day. After that, the
corresponding alarm indicator stays on the display.
TO USE SNOOZE (default snooze duration is 5 minutes)
When the alarm is sounding, press once, the alarm will stop temporarily and the
corresponding alarm indicator will keep flashing. The alarm will come on again after the
set snooze duration is over.
TO USE THE HI-MED-LO DIMMER (LED TIME DIGITS)
There is a 3-level brightness control for the LED clock display. Press to adjust
the brightness ( ) on the LED display. The brightness adjustment can only HI / MED / LO
be done when the brightness starts at position.HI
TO USE THE RING OF LED LIGHT
Press and hold button to turn on the ring of LED light, the brightness level of the
LED ring (Hi-Med-Lo) corresponds to the time display brightness (Hi-Med-Lo).
When the LED ring lights up, press button one at a time to adjust time display
brightness and LED ring brightness accordingly.
Press and hold button to turn off the ring of LED light. (The LCD dimmer
automatically adjusts after the RED LED light is switched off).
CHARGE YOUR MOBILE PHONE WITH USB PORT
Connect the charging cable of your mobile phone to the USB port at the back of the clock
and then connect the other end to the micro USB charging socket on your mobile phone.
The clock will charge the mobile phone automatically.
Note:
1. Make sure the cable supplied with your mobile phone is used for charging.
2. Make sure the adaptor supplied with this clock (5V 1.2A) is used to power it.
3. It is not possible to charge an iPad® or notepad from the USB socket on this clock.
4. When the alarms are sounding/active you can not charge phones etc using the USB
port.
TEST MODE
Press and hold button, strobe light flashing, shaker vibrating and buzzer ▲/ TEST
sounding.
TROUBLE SHOOTING
Your clock may display the incorrect time or may not function correctly due to electro-static
discharge or other interference like an electrical surge when an electric timer or heater
switches on/off (poor mains filtering). The mains adapter for the clock should only be
plugged into a mains wall socket, not a mains extension that is shared with electric heater
(or other high wattage equipment).
CARE OF YOUR PRODUCT
1. Place your clock on a stable surface, away from sources of direct sunlight or excessive
heat or moisture.
2. Protect your furniture when placing your unit on a natural wood and lacquered finish by
using a cloth or protective material between the unit and the furniture.
3. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger
agents such as benzene, cleaners containing alcohol, thinners or similar materials can
damage the surface of the unit.
SPECIFICATIONS
Alarm duration : 1 hour
Snooze duration Adjustable : 5 to 60 minutes
Default settings
Time format 24 hour
Time 0:00
Alarm 6:00
Alarm and shaker level HI
Alarm sound frequency F-1
Alarm sound level L1 (low)
Snooze duration 05 (5 minutes)
Audible alarm : up to 95 dBA at 1m
Express Warranty (Australia)
This Express Warranty is provided by Oricom International Pty Ltd ABN 46 086 116 369,
Unit 1, 4 Sovereign Place, South Windsor NSW 2756, herein after referred to as “Oricom”.
Oricom warrants that the product is free from defects in materials or workmanship during
the Express Warranty Period. This Express Warranty does not extend to any product from
which the serial number has been removed or was purchased outside of Australia.
The benefits of this Express Warranty are in addition to other rights and remedies you may
have under the Australian Consumer Law. Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure. In the event
of a minor failure, Oricom reserves the right to choose to repair or replace the product.
The Express Warranty Period will be a period of 12 months beginning on the date of
purchase of the product evidenced by your dated sales receipt. You are required to provide
proof of purchase as a condition of receiving Express Warranty services.
You are entitled to a replacement product or repair of the product at our discretion
according to the terms and conditions of this document if your product is found to be
faulty within the Express Warranty Period. This Express Warranty extends to the original
purchaser only and is not transferable.
Products distributed by Oricom are manufactured using new materials or new and used
materials equivalent to new in performance and reliability. Spare parts may be new
or equivalent to new. Spare parts are warranted to be free from defects in material or
workmanship for thirty (30) days or for the remainder of the Express Warranty Period
of the Oricom branded product in which they are installed, whichever is longer. During
the Express Warranty Period, Oricom will where possible repair and if not replace the
faulty product or part thereof. All component parts removed under this Express Warranty
become the property of Oricom. In the unlikely event that your Oricom product has a
recurring failure, Oricom may always, subject to the Competition and Consumer Act 2010,
at its discretion, elect to provide you with a replacement product of its choosing that is at
least equivalent to your product in performance.
No change to the conditions of this Express Warranty is valid unless it is made in writing
and signed by an authorised representative of Oricom.
Oricom will not be liable under this Express Warranty, and to the extent permitted by law
will not be liable for any defect, loss, damage or injury arising out of or in connection
with a:
1. Failure by you to adhere to the warnings and follow the instructions set out in this user
guide for the proper installation and use of the product;
2. Willful misconduct or deliberate misuse by you of the product;
3. Any external cause beyond our control, including but not limited to power failure,
lightning or over voltage; or
4. Modification to the product or services carried out on the product by anyone other than
Oricom or Oricom’s authorised service provider.
How to make a claim under your Express Warranty in Australia
Oricom has a simple warranty process for you to follow:
• Please call or email our Customer Support Team, 02 4574 8888 or support@oricom.
com.au.
• A Customer Support Team member will verify after troubleshooting with you if your product
qualifies under warranty. If so, they will give you a Product Return Authorisation number.
• We will then email a Return Authorisation form and a Repair Notice (if necessary), together
with instructions on how to return the product for warranty service.
Please note that if a Customer Support Team member advises that your product does
not qualify for return, this warranty does not apply to your product. Products that are
authorised to be returned to Oricom in Australia must include all of the following:
• A completed Return Authorisation form
• A copy of your Proof of Purchase (please keep your original copy)
• The faulty product, including all accessories.
Send the approved returns to:
Oricom International Pty Ltd
Locked Bag 658
South Windsor NSW 2756 Australia
Please note that this Express Warranty excludes expenses incurred by you in returning
any faulty product to us. You must arrange and pay any expenses incurred (including
postage, delivery, freight, transportation or insurance of the product) to return the faulty
product to us, however, p1-we will arrange delivery of the repaired or replaced faulty produc
to you.
Important Information
Repair Notice
Please be aware that the repair of your products may result in the loss of any user-
generated data (such as stored telephone numbers, text messages and contact
information). Please ensure that you have made a copy of any data saved on your product
before sending for repair. Please also be aware that products presented for repair may
be replaced by refurbished products or parts of the same type rather than being repaired.
Ref: 24062022
WNS80 USER GUIDE
KEEP THIS USER GUIDE FOR FUTURE REFERENCE
Always retain your proof of purchase in case of warranty service.
AUSTRALIA: www.oricom.com.au
A
M
ALARM
S
E
T
MO
DE
TIME
P
M
WAKE-T
O
-
BUZZ
ER
W
AKE-T
O-
VIBR IAT
O
N
W
AKE-TO
-
F
LASHING LE
D
U
P
TEST
ALARM
S
ET
ALARM
S
T
OP
DO
WN
S
E
T
S
N
OO
ZE
/
LI
G
HT
S
HAKE
R
USB charging cable
(not included)
5
V
1
.
2
A
6
W
A
C/
D
C
ADAPTOR
(Model No.
2
T
0069
)
Specyfikacje produktu
| Marka: | Oricom |
| Kategoria: | Niesklasyfikowane |
| Model: | Wake 'N' Shake Dynamite WNS80 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Oricom Wake 'N' Shake Dynamite WNS80, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Oricom
10 Grudnia 2024
21 Września 2024
18 Września 2024
17 Września 2024
14 Września 2024
13 Września 2024
12 Września 2024
12 Września 2024
12 Września 2024
9 Września 2024
Instrukcje Niesklasyfikowane
- GeoBox
- Grundfos
- Nimbus
- Winston
- Hamron
- Alula
- Koenig
- Klark Teknik
- Modbap Modular
- Nitek
- Outwell
- Warmup
- Accezz
- Airlux
- Flover
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025