Instrukcja obsługi Paasche 2000SI
Paasche
Niesklasyfikowane
2000SI
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Paasche 2000SI (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 11.5 użytkowników na średnio 4.6 gwiazdek
Strona 1/2
INTRODUCTION:
e SI Airbrush is simple in design and operation. Ideal for Hobbyists and Craers that are just learning to use an Airbrush. Available
o the shelf as size #3 with size #1 and #5 components available for your assembly. PTFE Packings.
OPERATING INSTRUCTIONS:
Adjustments in the ow of color are made by turning the Needle Chuck (#9) in to decrease, or out for increased ow. To spray,
press the Trigger (#6). To disassemble, loosen the Needle Locknut (#10) by holding the Needle Chuck (#9) rmly so it will not turn.
Unscrew the Needle Chuck from the Handle (#7) and remove the Handle. Now carefully remove the Needle (#16) and then the
Finger Button Assembly. e Head (#2) and Tip (#3) may now be removed. Reassembly should always be done with care, especially
when reinserting the Needle. Reverse the procedure used for disassembly. Aer the Needle has been gently pushed forward into
the tip, assemble the Needle Chuck (#9) and screw it in rmly. Hold the Needle Chuck while screwing the Needle Locknut (#10)
down to lock the needle. Caution should always be used when reinserting the Needle - too much pressure can damage the tip.
ADJUSTING OR REPLACING WORN PACKING WASHER:
1. If PTFE Packing & Packing Nut (#5) become worn or loose they must be tightened or replaced.
2. When replacing your PTFE Packing press Packing into the Packing Nut (#5). Use a small screwdriver to tighten packing nut
into shell until it is tight then back out one-half turn, may vary.
3. Now insert Trigger then Needle - you should feel a slight resistance to the needle as it goes through packing. If too loose/tight
adjust the Packing Nut with screwdriver until some slight resistance. Replace the Needle Chuck and the Needle Locknut.
Head Sizes - Patterns - Fluid Thickness
Size 1 - Tip size .022 inches or .55mm
- Used for ne detail. Pencil Line to 1’’ patterns
- Paint must be thinned further than 3 & 5 heads
Size 3 - Tip size .029 inches or .73mm
- Less detail than the size 1 head. 1/32’’ to 1-1/2’’ patterns
- Can spray slightly thicker paint than size 1 head
Size 5 - Tip Size .042 inches or 1.06mm
- Less detail than the size 3 head. 1/16’’ to 2’’ patterns
- Can spray slightly thicker paint than size 3 head
Working Pressures:
• Operating pressures 20-55 PSI; Maximum pressure 75 PSI
• 20-30 PSI is best for detail spraying w/ properly thinned paint
• Use the higher pressures for thicker material where ne detail is not critical or thin the paint to allow lower pressures.
Equipment Set-up:
e Airbrush is held in the same manner as a pen, with the index nger comfortably over the Trigger.
1. Attach airhose to air supply and to airbrush. If using a regulator, set pressure between 20 -30 PSI.
2. Attach the color cup or bottle assembly to color socket.
3. Spray with needle protecting cap #1 on or remove it for ner detail spraying.
TROUBLESHOOTING:
Bubbling in cup:
1. VLH Head #3 needs to be wrench tightened
Skipping or spitting:
1. Paint too thick -Reduce with thinner
2. Tip not seated -Tighten VLH Head with wrench
3. Tip split or damaged needle -Replace tip or needle
4. Needle or tip dirty -Clean and replace
5. Air pressure too low -Increase pressure or thin paint further (need 20 or more PSI to spray most paints)
Airbrush not spraying:
1. Clogged tip -Remove tip and clean
2. Needle not retracted -Adjust back knob
3. Loose VLH Head -Wrench tighten
4. Low air pressure -Increase pressure (need 20 or more PSI to spray most paints)
5. Bottle vent hole plugged -Use needle or pin to clear air hole
Sprays double line or heavy to one side:
1. Split tip or bent needle - Replace
2. Dirty tip or needle - Remove and clean
3. Tip not centered in head - Remove head and clean airbrush seat and tip seat then reassemble. Use wrench for head
INSTRUCTIONS AND PARTS LIST SI-8/06/2019
SI – Airbrush
Double Action - Internal Mix
Siphon Feed
Paasche® model SI features hand crafted
construction using quality materials. The body
is machined brass, polished and chrome plated.
Fluid tips are nickel silver, needles are stainless
steel & the needle packing is PTFE. Preferred
by professional and hobbyist alike.
Paasche Airbrush Co. 9511 58th Place Kenosha, WI. 53144 Phone:773/867-9191 Email: info @ paascheairbrush.com
Specyfikacje produktu
| Marka: | Paasche |
| Kategoria: | Niesklasyfikowane |
| Model: | 2000SI |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Paasche 2000SI, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Paasche
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Niesklasyfikowane
- Eurochron
- Inglesina
- Bbf
- Coors Light
- Medion
- James
- Vitamix
- ADE
- ASIWO
- Balance
- FED
- McIntosh
- Hotpoint
- Ocean Way Audio
- Yato
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025