Instrukcja obs艂ugi Paasche FP-4P
Paasche
Niesklasyfikowane
FP-4P
Przeczytaj poni偶ej 馃摉 instrukcj臋 obs艂ugi w j臋zyku polskim dla Paasche FP-4P (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja by艂a pomocna dla 28 os贸b i zosta艂a oceniona przez 14.5 u偶ytkownik贸w na 艣rednio 4.7 gwiazdek
Strona 1/2
INSTRUCTION AND PARTS LIST FP-4P 2/26/2018
Paasche Airbrush Company
9511 58th Place Kenosha, WI 53144
Website: paascheairbrush.com
E-Mail: info@paascheairbrush.com
Comes with LN-1/32 (Assembled) and LN-1/64, 3/64, and 1/16 Nibs loose
Total Length of Flow Pencil is 5 -1/2 inches.
Printed in the U.S.A.
INTRODUCTION:
The FP-4P Flow Pencil is used extensively by Cake Artists,
Bakers, and Home Bakers to decorate their Cakes, Cupcakes,
Cookies,etc. The Flow Pencil is easy to control and operate.
MIXING :
1. Proper mixing of Royal Icing & Butter Cream is essential for
continuous and uninterrupted flow.
2. Experiment with thinning of Icing for best flow.
3. Do not mix Icing in cup of Flow Pencil, use a separate
container and pour into cup only when Icing is at proper
consistency.
LOADING ICING: ( Tighten adjusting screw at rear of flow
pencil before loading Icing)
1. Remove FP-5 Cover, and pour premixed Icing into cup 3/4
full, Hold lid firmly and push plunger into cup, Pressure will
build and plunger will rise, thread lid onto cup.
2. Turning the MU-72 Adjusting Screw will control the
movement of the MU-65 Finger Lever Assembly which
controls the flow of Icing.
OPERATION:
1. Hold the FP-4P Flow Pencil in your hand as you would a
pencil or brush and place your finger lightly over the MU-65
Finger Lever. When ready to begin piping, pull back on the
MU-65 Finger Lever, when the icing begins to flow raise
the pencil up and pull in a backward motion off the surface
slightly.
2. Regulate the flow to the desired feed rate by turning
MU-72 Adjusting Screw.
3. When the plunger gets closer to the cap the flow rate will
slow down.
4. Practice on a Cake board before working on a actual cake.
5. Correct adjustment of controls and skill of operation will result
in uninterrupted and continuous piping.
CARE AND CLEANING:
1. Before storing FP-4P Flow Pencil clean it thoroughly. Rinse
cup and lid in hot water to clean out Icing,remove nib and clean
in hot water, wipe dry.
2. MU-49L Needle is held in position by MU-57 Needle Chuck
and VL-141 Locknut. Remove the needle by unscrewing the
MU-71 Handle and removing the spring. Loosen the VL-141
Locknut and then remove the needle for cleaning.
ADJUSTING OR REPLACING WORN PACKING WASHER:
1. If PTFE Packing-#6 becomes worn or loose it must be
tightened or replaced.
2. You will need a small screwdriver to remove or tighten the
Packing Nut.
3. When replacing your PTFE Packing press Packing onto the
Packing Nut-#6. Use a small screwdriver to tighten packing nut
into shell until it is tight then back out one-half turn, may vary.
4. Now insert needle - you should feel a slight resistance. If too
loose or too tight adjust the Packing Nut with screwdriver until
you feel some slight resistance.
5. Now completely re-assemble guts of Flow Pencil.
CAUTION: OVER TIGHTENING CUP WILL
CAUSE TRIGGER TO MALFUNCTION.
WARNING: Follow all safety precautions.
CAUTION: Never point flow pencil at face when pressurized.
FP-4P
(Pressure Fed)
Flow Pencil
OPERATING INSTRUCTIONS & REPLACEMENT PARTS
Specyfikacje produktu
| Marka: | Paasche |
| Kategoria: | Niesklasyfikowane |
| Model: | FP-4P |
Potrzebujesz pomocy?
Je艣li potrzebujesz pomocy z Paasche FP-4P, zadaj pytanie poni偶ej, a inni u偶ytkownicy Ci odpowiedz膮
Instrukcje Niesklasyfikowane Paasche
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
23 Wrze艣nia 2024
Instrukcje Niesklasyfikowane
- Verbatim
- Cambridge
- Caroma
- Applico
- RTS
- Daewoo
- Kincrome
- Sabco
- Cisco
- Califone
- Benidub
- Shuttle
- The Grainfather
- Hubble Connected
- Envivo
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025