Instrukcja obsługi PAC AP4-CH42
PAC
Niesklasyfikowane
AP4-CH42
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC AP4-CH42 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.6 gwiazdek
Strona 1/6
© 2024 Stinger. All rights reserved. PAC is a Power Brand of Stinger.
PAC-audio.com
Page 1
Rev 1
2/5/2024
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH42
The AP4-CH42 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range, xed
level head unit output, in conjunction with CAN messages, the AP4-CH42 delivers a variable 5v RMS pre-amp output with
fading, balance, equalization, and level control capabilities. The module also retains all audio from other vehicle features
such as factory navigation prompts, Bluetooth, uConnect, and parking sensor chimes. A data controlled remote amplier
turn on wire is also provided by the AP4-CH42. When used in conjunction with the APA-TOS1 (sold separately), the module
can provide a variable 2-channel ber optic digital audio output (TOSLINK).
Introduction and Features
Important Notes
1. Compatible with both amplied and non-amplied factory systems.
• Amplied Vehicles
• Compatible with all data-bus controlled amplied systems, no matter the screen size (including the 12" screen). To
identify these systems, look for logos on door speakers, tweeters, dash speakers or the subwoofer to conrm if the
vehicle has an amplied system (Alpine & Harmon Kardon). Some vehicles may not always have branded systems.
Unbranded amplied systems are generally identied by locating a center channel speaker or subwoofer
• Non-Amplied Vehicles
• Jeep Wrangler: Compatible with all screen sizes (5", 7" and 8.4").
• All other models: Only compatible in vehicles equipped with the 7" or 8.4" screen. Vehicles equipped with the 5"
screen are not compatible.
• If you are installing the AmpPRO in a vehicle that is not equipped with a factory amplier, you must add an amplier
to the vehicle's speakers, as the factory radio will no longer have a 4 channel variable output after it has been re-
congured by the AmpPRO. For example, you can not add only a subwoofer to a non-amplied vehicle, as the radio
will no longer power the cabin speakers properly.
• Non-amplied vehicles equipped with an Active Noise Cancellation (ANC) system require the ANC module to be
bypassed. This can be done manually or with the ANC bypass harness ANC-CH01. See page 2 Step 6d to re-congure
the factory radio.
2. If a factory amplier is present, it must remain connected and in the vehicle after the AmpPRO has been installed.
3. The remote output is rated at 2A of current. If more current is needed an external relay must be used.
4. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
5. The chime volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your particular
application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.
6. The level control knob must be connected in order to manually adjust the chime volume and minimum volume settings.
7. The factory radio's speed controlled volume and surround sound mode are not supported by the AP4 outputs.
8. When using the TOSLINK output (APA-TOS1 sold separately), DIP switch 1 must be on in order for all warning chimes to be
heard through the sound system (see page 2 Step 6a for details).
9. No adjustments can be made manually using the programming button, or the factory SWC when the module is connected to
a PC.
Module Layout
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
LED 1
TOSLINK Output
(APA-TOS1 sold separately)
Front Output
Ch. 1(L) and 2(R)
Rear Output
Ch. 3(L) and 4(R)
Non-Fading Output
Ch. 5(L) and 6(R)
LED 2
Specyfikacje produktu
| Marka: | PAC |
| Kategoria: | Niesklasyfikowane |
| Model: | AP4-CH42 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z PAC AP4-CH42, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane PAC
28 Grudnia 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
Instrukcje Niesklasyfikowane
- Jetway
- Jokari
- ProFlo
- PSSO
- Acoustic Solutions
- Zalman
- I-TEC
- Spear & Jackson
- AtomoSynth
- Swann
- Bontempi
- Bytecc
- Weller
- GP
- Kwantum
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025