Instrukcja obsługi PAC GM1A-RX
PAC
Niesklasyfikowane
GM1A-RX
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC GM1A-RX (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 8.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/5
GM1A-RX
Radio Replacement Interface
for select General Motors Vehicles
with Class II Data-Bus
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: V8
Date: 080118 Page 1
The GM1A-RX interface allows the replacement of a factory radio in select General Motors vehicles with the Class II Data-Bus.
Using this interface will retain factory features such as when the original radio warning chimes and the factory Bose amplier
is removed. The GM1A-RX provides data bus driven outputs such as retained accessory power (RAP), vehicle speed signal
(VSS), illumination, reverse trigger and parking brake. The GM1A-RX also provides an SWI Direct output for adding an optional
PAC Steering Wheel Control (SWC) retention interface (SWI-RC or SWI-CP2). Rear Seat Controls (RSC) if equipped will also
be retained with the SWI interface. You can also add multiple camera inputs to your aftermarket radio with Data-Bus controlled
automatic activation (front camera only) by connecting a VS41 into the expansion port on the GM1A-RX.
Module Layout
Important Notes
1. Does not retain OnStar.
2. Does not provide RSE audio to aftermarket radio.
3. Compatible in both Premium (Y91 / UQA) and Standard systems.
4. The included chime speaker should be used when: The vehicle has a standard Bose system (UQ7), the vehicle does not have
a factory amplier at all, or if you are connecting an aftermarket amplier to the cabin speakers.
5. The Programming Button and Adjustment Dial on the side of the interface have multiple functions. Please see Page 2 for
more details.
6. When used in conjunction with the add on camera controller (VS41) the GM1A-RX will only provide Data-Bus controlled
automatic activation for the front camera. Please refer to the vehicle specic VS41 instructions for more detail.
7. Fade is adjusted using the RadioPRO app, available at https://aampglobal.com/RadioProApp. The GM1A-RX module needs
to be connected to the vehicle, and the PC, to adjust chime volume.
8. In vehicles with Premium Bose (Y91 / UQA), dynamic fade is only supported by the GM1A-RT and GM1A-RST.
1. Wire your aftermarket radio to the GM1A-RX’s harness according to the wiring connections chart on the next page.
2. Plug Interface Connectors 1 and 2 into the appropriate port on the GM1A-RX interface (using the illustration above or the
label on the bottom of the interface).
3. Plug Interface connector 3 into the LOC-1 module. Connection will be dependent upon whether or not the vehicle has a
factory amplied system. Plug this connector into the appropriate port on the included line output converter (Part # LOC-1;
using the illustration on the next page or the text stamped into the housing). Improper connection will result in either very
over-driven audio in amplied systems or very low audio in non-amplied systems. If this occurs, disconnect the harness
from the LOC-1 Module, and connect it into the port on the opposite side of the LOC-1, the other connector on LOC-1 will
be let unused.
4. If you are also installing an optional SWC interface with the GM1A-RX, connect the SWI Direct Connector to the SWC
interface.
5. Remove the factory radio and plug in the GM1A-RX’s vehicle harness into the factory vehicle harness.
6. If necessary, program the SWC interface. Please see next section for more details.
7. If the vehicle has a standard Bose system, does not have a factory amplier at all, or if you are connecting an aftermarket
amplier to the cabin speakers, connect the chime speaker to the chime connector on the interface and install the chime
speaker in a place free of obstructions where it can be easily heard (usually low in the dash facing downward).
Installation Steps
Introduction and Features
USB Port
Expansion
Port
Interface
Connector 2
Interface
Connector 1
Chime
Connector
Programming
Button
Adjustment Dial
LED 2
LED 1
Specyfikacje produktu
| Marka: | PAC |
| Kategoria: | Niesklasyfikowane |
| Model: | GM1A-RX |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z PAC GM1A-RX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane PAC
28 Grudnia 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
Instrukcje Niesklasyfikowane
- Becken
- Madrix
- Homak
- FiiO
- Horizon Fitness
- Sifflus
- Cougar
- Carlsbro
- Yamazen
- Grillmeister
- Peach
- Mercusys
- Pericles
- Corel
- Ford
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025