Instrukcja obsługi Serge Ring

Serge Niesklasyfikowane Ring

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Serge Ring (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 26 osób i została oceniona przez 13.5 użytkowników na średnio 4.3 gwiazdek

Pobierz PDF
Strona 1/6
RANDOM*SOURCE
RANDOMSOURCE.NET 1
Serge RING
SERGE
Ring Modulator 2017
(RING) for Eurorack
The 2017 RING is an improved version of the late Serge
Ring Modulator (R9), designed by Serge himself for
Random*Source in 2017, more than 40 years after the
launch of the Serge Modular system.
To quote the Serge 1983 catalogue:
“Our new RING MODULATOR (RING) is a brand
new design which incorporates greatly improved
specications . Features include the following:
• A VERY CLEAN SOUND down to very low
signal levels (unlike conventional modulators where distortion increases at low levels) .
• 80 dbs OF CARRIER SIGNAL REJECTION.
• INAUDIBLE NOISE OUTPUT .
• NO SQUELCH CIRCUIT IS REQUIRED due to the low noise therefore annoying signal dropouts
and “pumping” effects are totally absent.
• INTERNAL WAVESHAPING OF CARRIER to add to modulation effects.
• The sum total of these design improvements is a Ring Modulator capable of treating the most subtle
acoustical signals, without the coloration typically associated with even the best previously available
ring modulators.
The versatility of the Serge Ring Modulator is enhanced by the added feature of voltage and manual control
of the entire spectrum of modulation possible: from zero modulation (i.e. the original, un-treated input
signal) through amplitude modulation to full ring modulation. This allows many shadings of effect, manual or
automatic with voltage controls. The ability to control the Carrier level manually and through voltage control
allows the output to be level controlled, as well. -Through the use of an internal signal processor for the
Carrier, additional effects can be produced by waveform modication of the carrier signal. When the module
is set to full Ring Modulation from the lower knob or voltage control, the output signal contains the sum and
RANDOM*SOURCE
RANDOMSOURCE.NET 2
Serge RING
difference frequencies of the Signal Input and the Carrier Input. If both signals are pure sine waves (only
one frequency component), the output will be a composite signal consisting two frequency components:
the sum and the difference frequency of the Signal and Carrier. If the Carrier level is increased beyond the
mid-position, then the carrier waveform will become slightly rounded, and new frequency components will
be produced. Each of these new components will also modulate with the Signal input to produce a sum
and difference frequency, and the output signal will become richer in harmonics. This effect. is unique to the
Serge Ring Modulator, and allows another dimension in timbral modication.
The Random*Source version of the RING for Euro is a licensed and authorized implementation of the new origi-
nal Serge design.
The Random*Source RING kit consists of a front panel and a pcb set with all SMT parts preinstalled. A couple of
through-hole parts (mostly capacitors) have to be installed (1uF caps only if not already installed in SMT!).
RANDOM*SOURCE
RANDOMSOURCE.NET 3
Serge RING
Pleasenote:
• TheRINGrequirescarefulcalibrationforbestresults.A2-channeloscilloscopeishiglyrecommended,
ifnotrequired.
• Themodulerequiresacoupleoflargercapacitors(10uFand4.7uF)andprovidesfootprintsforWIMA
lmcaps.Youshouldbeabletosubstituteothertypes(e.g.bipolarelectrolyticsforaudiouse),however,
theseareuntested.
• in(1uF,blackandsilvercubes)-If the main pcb already includes 3 large SMT capacitors
mostlikelythisisthecase-,youdonotneedtoinstallany1uFcapacitorsinthrough-hole-i.e.you
can leave the corresponding 1uF through-hole footprints empty.
• Useantistaticprecaution-trytoavoidtouchingtheSMTparts.
• Boardisdesignedtobepoweredbya+/-12VstabilizedPSUonly.(+/-15Visuntested).
BillofMaterials
Capacitors (min. 35V, 5mm lead spacing)
310uF FILM/PET,5mm WIMAMKS2B051001N00JSSD(5%recommended)
14.7uF FILM/PET,5mm WIMAMKS2orsimilar,5%recommended
31uF FILM/PET,5mm WIMAMKS2orsimilar-ONLYIFNOTALREADYINSTALLED
INSMT!
Trimmpots
11k Multiturn e.g.Bourns3296Y-1-102LForVishayT93YB102KT20
1100k Multiturn e.g.Bourns3296Y-1-104LForVishay
1100k Single-Turn e.g.Bourns3362P-1-104LForwhateverts)
Misc
1EuroPower
header
MTA-100powerconnector,Reichelt:WSL10G
5 Thonkiconn
Jacks
3.5mmJackSockets(PJ301M-12)fromThonk
4 Potentionmeter
50k
linear(B50K) Alpha9mmverticalpcbmount
availablefromThonk,Tayda,Mouser...
B100Kshouldalsowork
1Resistor22kor
24k
OPTIONALtoadjustthetaperofthe
MODEpot
CanbeeitherTH(0207)orSMT(0805,1206)
1
1
SILheader6pol
SILheader5polor4pol(checkmarkingsifusing4pol)
pinconnectors,linkingmainpcbtocomponent
pcb-usingprecisionstripsallowstobreakoff
piecesasneeded
4 Spacers+8matchingscrews(M3) 10mmorwhatevermatchestheSILheaders/
connectors

Specyfikacje produktu

Marka: Serge
Kategoria: Niesklasyfikowane
Model: Ring

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Serge Ring, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Serge

Serge

Serge Wave Multipliers Instrukcja

2 Października 2024
Serge

Serge Ring Instrukcja

1 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
Rock N Roller

Rock N Roller R14G Instrukcja

29 Stycznia 2025
Rock N Roller

Rock N Roller R6RT Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
Shimbol

Shimbol Memory I PRO Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025