Instrukcja obsługi Shelly Flood

Shelly inteligentny dom Flood

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Shelly Flood (2 stron) w kategorii inteligentny dom. Ta instrukcja była pomocna dla 66 osób i została oceniona przez 33.5 użytkowników na średnio 4.3 gwiazdek

Pobierz PDF

Strona 1/2

USER GUIDE

WIFI FLOOD SENSOR WITH

TEMPERATURE MEASUREMENT

Shelly® Flood by Allterco Robotics is intended to be placed

in a room/area in order to be aware of liquid leakage, and

monitor the temperature. Shelly Flood is battery powered,

with battery life up to 18 months. Shelly may work as a

standalone device or as an accessory to a home automa-

tion controller.

Battery Type:

3V DC - CR123A

Battery Life:

Up to 18 months

Electrical consumption:

• Static ≤5uA

• Awake ≤250mA

Temperature measurement range:

-40°C ÷ 60 °C (± 1°C)

Working temperature:

-40°C ÷ 60 °C

Dimensions (HxWxL):

70x19x19 mm

Radio protocol:

WiFi 802.11 b/g/n

Radio signal power:

1mW

Frequency:

2400 – 2500 MHz;

Operational range:

• up to 30 m outdoors

• up to 15 m indoors

Complies with EU standards:

• RE Directive 2014/53/EU

• LVD 2014/35/EU

• EMC 2004/108/WE

• RoHS2 2011/65/UE

Specications

Installation Instructions

CAUTION! Before beginning the installation please read

the accompanying documentation carefully and completely.

Failure to follow recommended procedures could lead to

malfunction, danger to your life or violation of the law. All-

terco Robotics is not responsible for any loss or damage in

case of incorrect installation or operation of this device.

CAUTION! Use the Device only with batteries which com-

ply with all applicable regulations. Inappropriate batteries

may cause a short circuit in the Device, which may damage it.

CAUTION! Do not allow children to play with the device,

especially with the Power Button. Keep the devices for re-

mote control of Shelly (mobile phones, tablets, PCs) away

from children.

Control your home with your voice

All Shelly devices are compatible with Amazons’ Alexa and

Googles’ assistant. Please see our step-by-step guides on:

https://shelly.cloud/compatibility/Alexa

https://shelly.cloud/compatibility/Assistant

Device „Wake Up“

To open the device, twist the top and bottom part of the

case counter clockwise.

Press the Button. The LED should ash slowly. This means

that Shelly is in AP mode. Press the Button again and the

LED will turn off and Shelly will be in „sleep“ mode.

LED States

• LED ashing slowly - AP Mode

• LED ashing quickly - STA Mode (No Cloud)

• LED still - STA Mode (Connected to Cloud)

• LED ashing quickly - FW Update (while in STA mode and

connected to Cloud)

Factory Reset

You can return your Shelly Flood to its Factory Settings by

pressing and holding the Button for 10 seconds. Upon suc-

cessful factory reset the LED will ash slowly.

Additional Features

Shelly allows control via HTTP from any other device, home

automation controller, mobile app or server.For more infor-

mation about the REST control protocol, please visit:

www.shelly.cloud developers@shelly.cloud or send a request to

MOBILE APPLICATION FOR SHELLY

The Shelly Cloud mobile application

Shelly Cloud gives you opportunity to control and adjust all

Shelly® devices from anywhere in the world. The only thing

you need is connection to the Internet and our mobile appli-

cation, installed on your smartphone or tablet. To install the

application please visit Google Play or App Store.

Registration

The rst time you open the Shelly Cloud mobile app, you

have to create an account which can manage all your

Shelly® devices.

Forgotten Password

In case you forget or lose your password, just enter the

e-mail address you have used in your registration. You will

then receive instructions on how to change your password.

WARNING! Be careful when you type your e-mail address

during the registration, as it will be used in case you forgot

your password.

After registering, create your rst

room (or rooms), where you are

going to add and use your Shelly

devices. Shelly Cloud allows easy

control and monitoring using a mo-

bile phone, tablet or PC.

Device Inclusion

To add a new Shelly device, connect it to the power grid

following the Installation Instructions included with the

Device.

Step 1

Place your Shelly Flood in the room where you want to use it.

Press the Button - the LED should turn on and ash slowly.

WARNING: If the LED does not ash slowly, press and

hold the Button for at least 10 seconds. The LED should

then ash quickly. If not, please repeat or contact our cus-

tomer support at:

support@shelly.cloud

Step 2

Choose “Add Device”.

In order to add more devices later, use the Menu at the top

right corner of the main screen and click “Add Device”.

Type the name and password for the WiFi network, to which

you want to add Shelly.

Step 3

- If using iOS: you will see the following screen (g. 4)

On your iOS device open Settings > WiFi and connect to the

WiFi network created by Shelly, e.g. ShellyFlood-35FA58.

- If using Android (g. 5) your phone will automatically scan

and include all new Shelly devices in the WiFi network, that

you dened.

Upon successful Device Inclusion to the WiFi network you

will see the following pop-up:

Step 4:

Approximately 30 seconds after discovery of any new de-

vices оn the local WiFi network, а list will be displayed by

default in the “Discovered Devices” room.

Step 5:

Select Discovered Devices and choose the Shelly device you

want to include in your account.

Step 6:

Enter a name

for the De-

vice. Choose

a Room, in

which the de-

vice has to be

po s i tione d.

You can choose an icon or upload a picture to make it easier

to recognize. Press “Save Device”.

Step 7:

To enable connection to the Shelly Cloud service for remote

control and monitoring of the Device, press “yes” on the

following pop-up.

Specyfikacje produktu

Marka:	Shelly
Kategoria:	inteligentny dom
Model:	Flood
Szerokość produktu:	70 mm
Głębokość produktu:	19 mm
Ilość na paczkę:	1 szt.
Technologia łączności:	Bezprzewodowy
Przeznaczenie:	Wewnątrz/Na wolnym powietrzu
Model:	Wbudowany
Dokładność:	1 °C
Standardowe interfejsy:	Sieć bezprzewodowa LAN
Typ przetwornika obrazu:	Czujnik temperatury i wilgotności
Zakres pomiaru temperatury:	-40 - 60 °C