Instrukcja obsługi Tube-Tech CL 1B
Tube-Tech
Niesklasyfikowane
CL 1B
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tube-Tech CL 1B (9 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 3.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/9
LYDKRAFT ApS
Mose Allé 20, DK 2610 Rødovre
Denmark
1
TUBE-TECH CL 1B
Compressor
DESCRIPTION.
The TUBE-TECH compressor CL 1B differs from many other compressors, in that the gain-
reduction element is made from a non-semiconductor element, which in itself has a very low
harmonic distortion and none of the non-linearity problems involved when using most
semiconductor elements. Furthermore there is no long-term degradation of the element thus
giving it almost infinite life. This element is placed after the input-transformer of the compressor
and followed by an all tube-based amplifier with a gain of -
dB to +30 dB.
Thus the signal is not fed through any semiconductor circuitry on its way to the output.
The amplifier consists of two tubes (valves) in push-pull configuration (one ECC 83 as the
pre-amp and phase splitter, and one ECC 82 as the output stage), and an output transformer.
The power supply for the pre-amp and phase splitter are stabilized and the heaters of both
tubes (valves) are fed with a stabilized DC voltage.
The whole amplifier (including input and output transformer) and the power supplies are placed
on one PC-board.
Both input and output are balanced (600
) and fully floating.
The in/out key switches the compressor in and out without clicks.
THE SIDECHAIN:
The side chain is the only part of the compressor that contains semiconductors. They are used
for three reasons: First they do not affect the sound reproduction, second they have a high slew
rate, which is of importance for the performance of the compressor and third they don't take up
much room.
It contains two J-FET quad op-amps, one npn-transistor and one FET-transistor, which handles
the signal for the gain-reduction element.
The compressor contains two time constants circuits:
1. Fixed attack and release times
2. Variable attack and release times
The
attack/release select
switch makes it possible to use these two circuits separately or
combine their functions.
This gives a feature not normally obtained in other compressors:
In the combined (fix. /man.) state the attack- and release controls makes it possible to
obtain a complex release-time slope. (See page 4)
(980112)
Specyfikacje produktu
| Marka: | Tube-Tech |
| Kategoria: | Niesklasyfikowane |
| Model: | CL 1B |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tube-Tech CL 1B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Tube-Tech
2 Października 2024
Instrukcje Niesklasyfikowane
- AdHoc
- Cricut
- Drawmer
- Motorola
- Python
- KiddyGuard
- Phase One
- Angler
- Victor
- Tunturi
- Eurosound
- Axor
- For_Q
- IDENTsmart
- On-Stage
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025