Instrukcja obsługi Botex Power Splitter 32-2
Botex
Niesklasyfikowane
Power Splitter 32-2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Botex Power Splitter 32-2 (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 10.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/1
DocID: 474324_14.05.2021
Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • Germany • www.thomann.de
Features
32A CEE power distributor for use on trusses
or on the oor
32A CEE in and output
6× earthed output socket 230V, each with a 16A fuse
(C16 circuit breaker)
Phase splitting
L1: CH1+2 // L
Residual curre
Control indica
For indoor use
M10 thread o
(max. 20 mm)
Technical specications
Dimensions W×H×D: 570×115×150mm
Weight: 4.2kg
Safety instructions
Intended use
This device is meant to be used for the distribution of mains power to
multiple loads. Any other use or use under other operating conditions
is considered to be improper and may result in personal injury or prop-
erty damage. No liability will be assumed for damages resulting from improper
use.
Dangers for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard! Ensure that children
do not detach any small parts (e.g. knobs or the like) from the unit. They could
swallow the pieces and choke! Never let children unattended use electrical de-
vices.
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt,
and strong vibrations.
Risk of re if the maximum current is exceeded
The device can power other devices via a lockable Power Twist output socket.
The current consumption of all serially connected other devices must not ex-
ceed 16 A, otherwise you risk injuries and irreparable damages of the device.
Connect just so many devices to the output socket that the maximum current
consumption is not exceeded.
Ensure the correct dimensioning (wire cross section) of the used power cords of
all serially connected devices.
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers. There are no user-serviceable parts inside.
th a
protective contact plug. Do not modify the mains cable or the plug. Failure to
do so could result in electric shock/death or re. If in doubt, seek advice from a
registered electrician.
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or re.
Handling the power cord
Do not place the device or speaker boxes or similar on the power cord and be
careful not to pinch it. Never tie a knot in the power cord or tie it with other
cables. Route the power cord so that no one steps on or trips over it. A damaged
power cord can cause a re or electric shock. Replace any broken cables.
Protecting the environment
For the transport and protective packaging, environmentally friendly
materials have been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of. Do not
just dispose of these materials with your normal household waste, but make
sure that they are collected for recycling. Please follow the notes and markings
on the packaging.
This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) in its currently valid version. Do not dispose
of your old device with your normal household waste. Dispose of this
product through an approved waste disposal rm or through your local
waste facility. Comply with the rules and regulations that apply in your country.
If in doubt, consult your local waste disposal facility.
EN
Power Splitter 32-2 | Power Distributor
Specyfikacje produktu
| Marka: | Botex |
| Kategoria: | Niesklasyfikowane |
| Model: | Power Splitter 32-2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Botex Power Splitter 32-2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Botex
22 Września 2024
22 Września 2024
22 Września 2024
21 Września 2024
21 Września 2024
20 Września 2024
19 Września 2024
18 Września 2024
17 Września 2024
8 Września 2024
Instrukcje Niesklasyfikowane
- Niesklasyfikowane HiKOKI
- Niesklasyfikowane Crimson
- Niesklasyfikowane Calligaris .com
- Niesklasyfikowane Ixxat
- Niesklasyfikowane Antelope Audio
- Niesklasyfikowane Truma
- Niesklasyfikowane GA.MA
- Niesklasyfikowane Swiss Eye
- Niesklasyfikowane Rossmax
- Niesklasyfikowane FitterFirst
- Niesklasyfikowane Prixton
- Niesklasyfikowane Switel
- Niesklasyfikowane Schütte
- Niesklasyfikowane Arduino
- Niesklasyfikowane OSO
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025