Instrukcja obsługi DPW Design Mix
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DPW Design Mix (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 4.5 użytkowników na średnio 3.5 gwiazdek
Strona 1/2
Mix
The Mix is a compact 4 channel stereo mixer that also can be set up to be set up to be up to 8
channels of mono with crossfading in 4 groups. It also has a built in soft knee limiter for subtle level
control or harder creative coloring of the sound.
It is designed to be a flexible compact part of your system. As the main mixer for a small system or
you have a few distributed in your bigger system and use one to collect the signals from all of them
sa the main out.
The unit can be used as a utility module for control voltages as well as for audio. It is DC coupled.
Inputs, stereo mode
There are 4 channels of stereo input with volume and pan control.
When using one of the channels with mono in stereo mode you can
connect to either left or right channel. The left and right inputs are
normalled to each other.
All channels have one time amplification (unity gain) when the Vol
knob is turned fully clockwise.
The module is designed to never clip internally but the levels can get
high at the output stage. So the output stage has a controlled nice
sounding round clipping that limits the output to +/- 10V.
Use the output LEDs as a guide to get an output level that doesn't
clip.
The bandwidth of the module in this mode is 150 kHz (-3dB point) so
there is basically no unwanted frequency dependent phase shift in the
audio range.
The extended bandwidth will also make the sound of the mixer very
transparent.
M switches
The M switches (mono) turns the channels left and right input to dual
mono with the Vol knob as a volume for both and the Pan becomes a
mono crossfade between the left and right input.
The M switches affects the channels in two groups. The upper M switch affects channel 1 and 2.
the lower affects channel 3 and 4.
This means that engaging one or two M switches can give you 4 mono with two groups of
crossfade plus two stereo channels or 8 channels of mono with 4 groups of crossfade.
The crossfade can be used as a performance feature to gradually crossfade from one part of your
system to an other or to build more complex voices.
If only one side of a channel is connected, the M switch for that channel is on and Pan is in center
possition you will get a two times amplification of that channel. Can be used for extra boost where
needed.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-M1 Rev B
Specyfikacje produktu
| Marka: | DPW Design |
| Kategoria: | Niesklasyfikowane |
| Model: | Mix |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z DPW Design Mix, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane DPW Design
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
25 Września 2024
Instrukcje Niesklasyfikowane
- Life Gear
- Hamilton Beach
- Profile
- Gumdrop
- DLO
- Linksys
- Smartwares
- Merax
- Satisfyer
- Winix
- Swedish Posture
- Winston
- Guardian
- Spear & Jackson
- X-Sense
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025