Instrukcja obsługi DPW Design Shape


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DPW Design Shape (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 34 osób i została oceniona przez 17.5 użytkowników na średnio 4.6 gwiazdek

Strona 1/3
Shape SH-1, Spectral Enhancer
The SH-1 is a is a combination of a compressor/limiter and a dynamically dependent spectral enhancer.
It works very well as a pseudo stereo device where it can do everything from subtle to extreme spectrally
enhanced stereo spreading.
It can also be like an odd take of something almost like a transient designer or a very open sounding
distortion. It is an all analoge module. A module for sonic experimentation.
A short description of what the module is doing:
It consists of mainly two parts. A compression part and a calculation part.
The comperssion part is designed to be as transparent as possible. That said, all types of compression adds
distortion that can be seen as added upper harmonics that are depending on the signal in.
The calculation part gives you Tran and Tail. Tran can be trimmed via Trim to be ony the newly produced
upper harmonics from the compressor. For a very transient sound this means that you can trim the the Tran
output to be a very short sound just during the transient part of the incoming sound.
The calculation for the Tail output is the clean sound minus the newly produced upper harmonics from the
compressor, but from a different circuit than for Tran. So it is not affected by Trim.
This makes the sound on Tail to be mainly the tail of a transient sound.
The effect out on Trim and Tail is highly dependent on the nonlinier character of the compression via the
drive. The more compression and the more complex signal in, the bigger the effect on Tran and Tail.
The SH-1 works very well for parralell processing as it has very low internal phase delay.
Controls
In
The signal in.
Drive
Level of compression, how hard it is driven. Affects everything in the module.
The compressed signal goes in to the mix section and also direct out on
Comp.
The maximum compression is 10 times. Because it has that much gain it is
designed to brick wall limit to +/-5V. So you will never get ugly clipping no
matter how hard you drive it.
Trim
Is for the Tran calculation together with Drive. It only affects Tran.
The Trim LED it there to help you see when only the newly produced
harmonics are present on Tran. Red too low, green too high and amber as
close as you can get. The LED is mainly there as a guide. You will have to
compensate Trim if you change Drive.
For transient material the LED will flash.
Trim can be used to get a more open distorted version of your sound on
Tran. Experimet and see what you like. It will probably be in the area where
the Trim LED is green.
Clean
The ammount of clean signal direct from In to the Mix out.
The Mix out is a combination of Clean, Comp, Tran and Tail.
The Mix LED shows when the Mix output is higher than 6V. Nothing bad
happens when it is lit. It is just a visual help for levels.
Comp
The direct output of the compressor controlled by the Drive.
The Comp knob sets the ammount of compressed signal in to the Mix out.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-SH-1 Rev B


Specyfikacje produktu

Marka: DPW Design
Kategoria: Niesklasyfikowane
Model: Shape

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DPW Design Shape, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane DPW Design

DPW Design

DPW Design Zero 2 Instrukcja

25 Września 2024
DPW Design

DPW Design Shape Instrukcja

25 Września 2024
DPW Design

DPW Design Switch Instrukcja

25 Września 2024
DPW Design

DPW Design Limit Instrukcja

25 Września 2024
DPW Design

DPW Design AV2 Instrukcja

25 Września 2024
DPW Design

DPW Design Mix Instrukcja

25 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025