Instrukcja obsługi Intex 28002E


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Intex 28002E (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 28 osób i została oceniona przez 14.5 użytkowników na średnio 4.1 gwiazdek

Strona 1/4
(223PO) POOL VACUUM & SKIMMER ENGLISH SIZE: 4.875” X 7.25” 04/24/2013
223
PO
SAVE THIS INSTRUCTIONS
223PO-R0-1404
POOL MAINTENANCE KIT ASSEMBLY AND
OPERATING INSTRUCTIONS
IMPORTANT: READ AND UNDERSTAND THE INSTRUCTIONS COMPLETELY BEFORE
STARTING ASSEMBLY.
POOL VACUUM ASSEMBLY INSTRUCTIONS
1. Turn handle and handle and slide each section to extend or shorten the A B clockwise
length of the telescoping shaft . Turn to lock each section in place. (6) counterclockwise
Clip the hose mount on the shaft.(4)
2. Tie the debris collection bag onto the cleaning head opening opposite from the (3)
garden hose connection, as you would tie shoelaces.
3. The cleaning head has a plastic spring that connects to the bottom shaft. Align (2) (1)
the plastic spring located inside the cleaning head with the holes drilled in the shaft.
Gently squeeze together the plastic spring tips so that the shaft slips onto the cleaning
head and the spring "pops" into the pre-drilled holes.
4. Depending on the type of garden hose connect the hose to the side opposite the debris
bag. Mount the garden hose on the shaft by clipping in the hose mount (4).
IMPORTANT: The flat washer must be placed into coupling before garden hose is
connected.
5. The pool vacuum is now ready to use.
POOL VACUUM OPERATING INSTRUCTIONS
1. Connect the garden hose to the water spigot and turn on the water.
NOTE: The water pressure varies in each community so testing will have to be
done to find the correct hose water pressure for optimum cleaning.
2. In soft gentle strokes "sweep" the entire bottom surface of the pool liner until it is clear of
debris.
3. Turn water "OFF", remove the pool vacuum from the pool, disconnect and place the
garden hose in a safe area.
4. Untie and clean the debris collection bag. Allow the debris bag to air dry. Retie the
collection bag onto the cleaning head.
5. Store the pool vacuum in an area where it will not be a safety hazard.
POOL SKIMMER ASSEMBLY AND OPERATING INSTRUCTIONS
1. The pool skimmer uses the same shaft as the pool vacuum’s.
2. The skimmer net has a plastic spring that connects to the bottom shaft. Align the (5) (1)
plastic spring located inside the net with the holes drilled in the shaft. Gently squeeze
together the plastic spring tips so that the shaft slips onto the net and the spring "POPS"
into the pre-drilled holes.
3. Gently sweep the surface of the pool with the skimmer net removing floating leaves, etc.


Specyfikacje produktu

Marka: Intex
Kategoria: Niesklasyfikowane
Model: 28002E

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Intex 28002E, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Intex

Intex

Intex River Run Instrukcja

26 Stycznia 2025
Intex

Intex 58854EU Instrukcja

14 Października 2024
Intex

Intex 28002E Instrukcja

6 Października 2024
Intex

Intex 28050E Instrukcja

15 Września 2024
Intex

Intex Solar Blanket Instrukcja

10 Września 2024
Intex

Intex 55612 Instrukcja

9 Września 2024
Intex

Intex 28061E Instrukcja

5 Września 2024
Intex

Intex 28211EH Instrukcja

5 Września 2024
Intex

Intex 58847EU Instrukcja

2 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025