Instrukcja obsługi Boss Fuzz FZ-1W
Boss
Niesklasyfikowane
Fuzz FZ-1W
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss Fuzz FZ-1W (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 23 osób i została oceniona przez 12 użytkowników na średnio 4.8 gwiazdek
Strona 1/1
*5100078040-01*
FZ-1W Owner’s Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
English
Panel Descriptions
© 2021 Roland Corporation
DC IN jack
AC adaptor
(PSA series; sold
separately)
In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC
adaptor (PSA series; sold separately).
* Use only the specied AC adaptor (PSA series; sold
separately), and connect it to an AC outlet of the correct
voltage.
* If the AC adaptor is connected while a battery is installed,
the power supply is drawn from the AC adaptor.
Precautions When Connecting
• To prevent malfunction and equipment failure, always
turn down the volume, and turn o all the units
before making any connections.
• Once everything is properly connected, be sure to
follow the procedure below to turn on their power. If
you turn on equipment in the wrong order, you risk
causing malfunction or equipment failure.
When powering
up:
Turn on the power to your
guitar amp last.
When powering
down:
Turn o the power to your
guitar amp rst.
• Before turning the unit on/o, always be sure to turn
the volume down. Even with the volume turned
down, you might hear some sound when switching
the unit on/o. However, this is normal and does not
indicate a malfunction.
• Do not use connection cables that contain a built-in
resistor.
Use of Battery
• The life of the included battery may be limited as its
primary purpose was for testing during assembly.
• If you handle batteries improperly, you risk explosion
and uid leakage. Make sure that you carefully
observe all of the items related to batteries that are
listed in “USING THE UNIT SAFELY” and “IMPORTANT
NOTES” (supplied on a separate sheet).
• When operating on battery power only, the unit’s
indicator will become dim when battery power gets
too low. Replace the battery as soon as possible.
• If the batteries run extremely low, the sound may
distort, but this does not indicate a malfunction. If
this occurs, please replace the batteries or use the AC
adaptor (sold separately).
• Batteries should always be installed or replaced
before connecting any other devices. This way, you
can prevent malfunction and damage.
Changing the Battery
1. Hold down the pedal and loosen the
thumbscrew, then open the pedal
upward.
Thumbscrew
Battery housing
Pedal
Spring base
Coil spring
Guide bush
hole
Battery snap
cord
Battery
snap
Battery
* The pedal can be opened without detaching the
thumbscrew completely.
2. Remove the old battery from the battery
housing, and remove the snap cord
connected to it.
3. Connect the snap cord to the new
battery, and place the battery inside the
battery housing.
* Be sure to carefully observe the battery’s polarity (+
versus -).
4. Slip the coil spring onto the spring base
on the back of the pedal, and then close
the pedal.
* Carefully avoid getting the snap cord caught in the
pedal, coil spring, and battery housing.
5. Finally, hold down the pedal while
tightening the thumbscrew into the
guide bush hole.
Main Specications
Nominal Input
Level -20 dBu
Input Impedance 1 MΩ (eect o)
22 kΩ (eect on)
Nominal Output
Level -20 dBu
Output Impedance 1 kΩ
Recommended
Load Impedance 10 kΩ or greater
Power Supply
Alkaline battery (9 V, 6LR61 or 6LF22)
or Carbon-zinc battery (9 V, 6F22)
AC adaptor (PSA series: sold
separately)
Dimensions
73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H)
inches
Weight
(including battery)
430 g
1 lb
Accessories
Owner’s manual, Leaet “USING THE
UNIT SAFELY,” Alkaline battery (9 V,
6LR61 or 6LF22)
Option
(sold separately) AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the
product at the time that the document was issued.
For the latest information, refer to the Roland
website.
https://roland.cm/fz-1w_spec
* Roland, BOSS, and WAZA CRAFT are either
registered trademarks or trademarks of Roland
Corporation in the United States and/or other
countries.
[LEVEL] knob
This knob adjusts the volume of the eect sound.
* No sound will be heard when this knob is rotated
completely counterclockwise.
[TONE] knob
Adjusts the brightness of the eect sound. Turning the knob
clockwise brightens the sound.
OUTPUT jack
Use this 1/4” output jack to connect to
the input of your guitar amplier or the
input of additional eect unit. Guitar amplier
Pedal switch
This switch turns the eects ON/OFF.
CHECK indicator
This indicator shows whether an eect is ON/OFF, and doubles as the Battery
Check indicator.
The indicator lights when an eect is ON.
* The brightness of the CHECK indicator (LED) will dim as the battery lowers.
Replace the battery when the LED is dim or does not light. For instructions,
refer to “Changing the Battery.”
[FUZZ] knob
Rotating the knob clockwise increases the gain and fuzz
eect.
* If you set this knob too high, the noise will increase and
oscillation may occur.
Mode switch
Switches the sound variation.
V (Vintage)
Reminiscent of the fuzz sounds of the
1960’s, this is BOSS’s original vintage
fuzz sound.
M (Modern) A fat yet smooth next-generation fuzz
sound with high gain.
INPUT jack
Electric guitar
This jack accepts input signals
(coming from a guitar, some other
musical instrument, or another
eects unit).
* The INPUT jack also serves as the power switch. Power is
turned on whenever a plug is inserted into the INPUT jack,
and is turned o when the plug is disconnected. When not
using the unit, you should disconnect the plug connected
to the INPUT jack.
Thumbscrew
When this screw is loosened, the
pedal will open, allowing you to
change the battery.
* For instructions on changing
the battery, refer to “Changing
the Battery.”
Specyfikacje produktu
| Marka: | Boss |
| Kategoria: | Niesklasyfikowane |
| Model: | Fuzz FZ-1W |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Boss Fuzz FZ-1W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Boss
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
Instrukcje Niesklasyfikowane
- Lynx Technik
- ASIWO
- X-Rite
- RCA
- Sightmark
- AstrHori
- Sven
- Tru Components
- Simplecom
- BabyGO
- ESX
- Galaxy Audio
- Simrad
- Pfister
- BWT
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025