Instrukcja obsługi Boss SY-1
Boss
Niesklasyfikowane
SY-1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss SY-1 (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/1
* 5 1 0 0 0 6 6 0 8 4 - 0 2 *
FS-7
FS-5U FS-6
For the USA
SUPPLIER’S DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
SY-1
Guitar Eects
Roland Corporation U.S.
5100 S. Eastern Avenue Los Angeles, CA 90040-2938
(323) 890-3700
Owner’s Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
English
List of Types
TYPE Explanation
LEAD 1/2 Sounds suitable for solo or lead.
PAD Soft sounds that ll-in gaps between notes.
BASS Bass synth sounds.
STR Synth strings sounds.
ORGN Organ sounds.
BELL Sounds with metallic resonance.
SFX 1/2 Sound eects or distinctive sounds.
SEQ 1/2 Sounds whose pitch or character changes rhythmically.
Precautions When Connecting
* To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
* Once the connections have been completed, turn on power
to your various devices in the order specied. By turning on
devices in the wrong order, you risk causing malfunction and/
or damage to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
* Before turning the unit on/o, always be sure to turn the
volume down. Even with the volume turned down, you might
hear some sound when switching the unit on/o. However,
this is normal and does not indicate a malfunction.
* Do not use connection cables that contain a built-in resistor.
* Use only the specied expression pedal. By connecting any
other expression pedals, you risk causing malfunction and/or
damage to the unit.
* You must turn o the power when connecting or
disconnecting an external footswitch. If you connect or
disconnect a footswitch while the power is on, the SOUND
HOLD function might remain on, or might not work. If the
SOUND HOLD function remains on or does not work, turn the
power o and then on again.
* When using this unit together with another eect unit, this
unit must be connected at the beginning of the chain. If an
eect-processed guitar or bass sound is input to this unit, it
might not work correctly.
Use of Battery
* The life of the included battery may be limited as its primary
purpose was for testing during assembly.
* If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY”
and “IMPORTANT NOTES” (supplied on a separate sheet).
* When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
* Batteries should always be installed or replaced before
connecting any other devices. This way, you can prevent
malfunction and damage.
* If operating this unit on battery, please use alkaline battery.
Changing the Battery
1. Hold down the
pedal and loosen
the thumbscrew,
then open the
pedal upward.
* The pedal can be
opened without
detaching the
thumbscrew
completely.
2. Remove the old
battery from the
battery housing,
and remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil spring, and
battery housing.
5. Finally, hold down the pedal while tightening the
thumbscrew into the guide bush hole.
Main Specications
BOSS SY-1: Synthesizer
Nominal Input Level -20 dBu
Input Impedance 2.2 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance 10 kΩ or greater
Power Supply DC 9 V: Alkaline battery (9 V, 6LR61)
AC adaptor (PSA series: sold separately)
Current Draw
85 mA
* Expected battery life under continuous
use:
Alkaline battery: Approx. 3 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight
(including battery)
450 g
1 lb
Accessories
Owner’s Manual, Leaet (“USING THE UNIT
SAFELY,“ “IMPORTANT NOTES,“ and “Informa-
tion“), Alkaline battery (9 V, 6LR61)
Option
(sold separately)
AC adaptor (PSA-series)
Footswitch: FS-5U
Dual footswitch: FS-6, FS-7
Expression pedal: FV-500H, FV-500L, EV-30,
Roland EV-5
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
* Roland and BOSS are either registered trademarks or
trademarks of Roland Corporation in the United States and/or
other countries.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
Battery
© 2019 Roland Corporation
INPUT jack
This jack accepts input signals coming from a guitar or bass.
Guitar/BASS
SEND/RETURN jacks
Connect the SEND jack to the input, and RETURN jack to
the output of an eect unit that you’re using to process
the audio signal of your guitar/bass.
OUTPUT jack
Use this 1/4” output jack to connect to the input of
your guitar amplier or the input of additional eect
unit.
Guitar Amp
DC IN jack
In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (BOSS PSA series;
sold separately).
* Use only the specied AC adaptor (PSA series; sold separately), and connect it to an AC outlet
of the correct voltage.
* If the AC adaptor is connected while a battery is installed, the power
supply is drawn from the AC adaptor.
CHECK indicator
This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.
The indicator lights when an eect is ON.
* The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace
the battery when the LED is dim or does not light. For instructions, refer to “Changing
the Battery.”
* The CHECK indicator shows whether the eect is on or o, and indicates the dierent
functions. It does not indicate whether the power to the device is on or not.
TONE/RATE knob /DEPTH knob
These knobs adjust the sound of the eect that’s selected by TYPE and
VARIATION.
Pedal switch
This switch turns the eects ON/OFF.
SOUND HOLD function
1. When you hear the eect sound (synth sound) that you want to
hold, press the pedal switch once again and keep holding it down.
The hold function stays on while you keep holding down the pedal switch,
and the CHECK indicator blinks. You continue to hear the eect sound in
this state.
2. To turn o the hold function, take your foot o the pedal switch.
The CHECK indicator turns on, and the unit is in the normal eect-on state.
* If a footswitch is connected to the EXP/CTL jack, this function moves
from this unit to the footswitch.
Panel Descriptions
VARIATION knob
This knob selects variations 1–11 of the sound selected by TYPE.
GUITAR/BASS switch
This switch selects settings that are suitable for a guitar or a bass.
TYPE knob
This knob switches the type of synth sound.
(see the “List of Types” below)
EFFECT knob
This knob adjusts the volume of the eect sound (synth sound).
DIRECT knob
This knob adjusts the volume of the direct sound.
If a device is connected to the SEND/RETURN jacks, this knob adjusts its volume.
EXP/CTL jack You can connect an external footswitch (sold separately)
or expression pedal (sold separately) to this jack.
If a footswitch is connected, you can use the footswitch
to operate the SOUND HOLD function.
If a dual footswitch is connected, you can also control (in
addition to the SOUND HOLD function) either the pitch
or the tempo according to the sound that’s selected by
the knobs.
Pitch The pitch rises one octave while you hold down the switch.
Tempo You can enter the tempo by pressing the footswitch at the desired
interval.
If an expression pedal is connected, you can use it to control the TONE/RATE
eect. In this case, the position of the TONE/RATE knob is the maximum value of
the expression pedal.
Mode and polarity switch settings for the footswitch
Thumbscrew
When this screw is loosened, the
pedal will open, allowing you to
change the battery.
* For instructions on changing
the battery, refer to
“Changing the Battery.”
* The INPUT jack also serves as the
power switch. Power is turned on
whenever a plug is inserted into the
INPUT jack, and is turned o when
the plug is disconnected. When not
using the unit, you should disconnect
any cord connected to the INPUT
jack.
Specyfikacje produktu
| Marka: | Boss |
| Kategoria: | Niesklasyfikowane |
| Model: | SY-1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Boss SY-1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Boss
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
15 Grudnia 2024
Instrukcje Niesklasyfikowane
- V7
- Shadow
- Skaarhoj
- Consul
- Heller
- Elektron
- Stamos
- Klipsch
- GolfBuddy
- Alfresco
- Shindaiwa
- FontaFit
- Oscium
- Holosun
- IsoAcoustics
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025